GENERAL (serv.man2). How to get into service mode - Sharp TV Technical Bulletin (repair manual)

general (serv.man2) technical bulletin
Model
GENERAL (serv.man2)
Pages
7
Size
124.34 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
TV / CTR / How to get into service mode
File
general-sm2.pdf
Date

Read Sharp GENERAL (serv.man2) Technical Bulletin online

Sharp Electronics (UK) Limited
Reference AVW060599/1
Revision  1
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
CTV990504
Month of Issue: May 1999
        Classification:          White
TELEVISION TECHNICAL BULLETIN
Page 1 of 7
MODELS
BCTVA Chassis
4BS-C Chassis
CA1 Chassis
CA10 Chassis
CW100 Chassis
CS Chassis
D3000 Chassis
DECO-4 Chassis
DECO-5 Chassis
4BS-B Chassis
4BS-A Chassis
5BS- A Chassis
S3B Chassis
To assist with the adjustments of the above chassis, the list below details how to enter the various
service modes.
BCTVA Chassis
66AS06H, DV5932H, DV5935H, DV5937H and DV6635H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4.  SERVICE SOFTWARE will appear on the screen
5.  Remove the jumper wire
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp Electronics (UK) Limited
Reference AVW060599/1
Revision  1
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
CTV990504
Month of Issue: May 1999
        Classification:          White
TELEVISION TECHNICAL BULLETIN
Page 2 of 7
4BS-C Chassis
DV5940H, DV6640H and 66AS05H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Text Unit
4.  SERVICE SOFTWARE will appear on the screen
5.  Remove the jumper wire
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CA1 Chassis
37DM23H, 37DT25H, 37ET35H, 37EM33H and 51DT25H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver off using the mains button
4.  Press the volume down and channel up buttons on the front of the receiver at the same time
5.  Keeping these buttons pressed, turn the mains on
6.  When the set starts up it will be in service mode
7.  Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control.
Sharp Electronics (UK) Limited
Reference AVW060599/1
Revision  1
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
CTV990504
Month of Issue: May 1999
        Classification:          White
TELEVISION TECHNICAL BULLETIN
Page 3 of 7
CA10 Chassis
51DS02H, 51DS03H, 51DS05H, 59DS03H, 59DS05H, 59ES03H, 59ES05H, 59ESD7H, 66DS03H, 66DS05H,
66ES05H and 66ESD7H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver off using the mains button
4.  Press the volume down and channel up buttons on the front of the receiver at the same time
5.  Keeping these buttons pressed, turn the mains on
6.  When the set starts up it will be in service mode
7.  Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CS Chassis
51CS03H, 51CS05H, 59CS03H, 59CS05H, 59CSD8H, 66CS03H, 66CS05H and 66CSD8H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver off using the mains button
4.  Press the volume down and channel up buttons on the front of the receiver at the same time
5.  Keeping these buttons pressed, turn the mains on
6.  When the set starts up it will be in service mode
7.  Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CW100 Chassis
66DW18H and 76DW18H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver off using the mains button
4.  Press the volume down and channel up buttons on the front of the receiver at the same time
5.  Keeping these buttons pressed, turn the mains on
6.  When the set starts up it will be in service mode
7.  Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp Electronics (UK) Limited
Reference AVW060599/1
Revision  1
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
CTV990504
Month of Issue: May 1999
        Classification:          White
TELEVISION TECHNICAL BULLETIN
Page 4 of 7
D3000 Chassis
DV51083H, DV5903H, DV59083H, DV6603H and DV66083H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver on
4.  Press the service switch (S1401) located on the Video PWB
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
4BS-B Chassis
DV5165H and DV5180H
1.  Connect a test pattern to the antenna terminal
2.  Tune to this signal
3.  Turn the receiver off using the mains button
4.  Press the volume down and channel up buttons on the front of the receiver at the same time
5.  Keeping these buttons pressed, turn the mains on
6.  When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7.  Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Page of 7

Download Sharp GENERAL (serv.man2) Technical Bulletin

Here you can read online and download Sharp GENERAL (serv.man2) Technical Bulletin in PDF. GENERAL (serv.man2) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp GENERAL (serv.man2) CTR. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.