Read Sharp GENERAL (serv.man2) Technical Bulletin online
Sharp Electronics (UK) Limited
Reference AVW060599/1
Revision 1
White – Carry out as required, Yellow – Carry out as required and whenever the unit comes in for service, Red – Carry out on all units
CTV990504
Month of Issue: May 1999
Classification: White
TELEVISION TECHNICAL BULLETIN
Page 3 of 7
CA10 Chassis
51DS02H, 51DS03H, 51DS05H, 59DS03H, 59DS05H, 59ES03H, 59ES05H, 59ESD7H, 66DS03H, 66DS05H,
66ES05H and 66ESD7H
66ES05H and 66ESD7H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CS Chassis
51CS03H, 51CS05H, 59CS03H, 59CS05H, 59CSD8H, 66CS03H, 66CS05H and 66CSD8H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
CW100 Chassis
66DW18H and 76DW18H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Click on the first or last page to see other GENERAL (serv.man2) service manuals if exist.