Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N SIMULATION 5 – 10
<4K Finisher saddle unit>
3-10
Purpose
Adjustment
Function (Purpose)
Adjust the finisher.
Section
Finisher
Operation/Procedure
1)
Select an adjustment target item with scroll key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<Inner finisher>
<1K Saddle stitch finisher>
NOTE: "A: SADDLE POSITION (Saddle binding position adjust-
ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment"
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting 5.0mm)
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting 5.0mm)
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
<4K Finisher>
<4K Saddle finisher>
FINRRS
Inlet port roller separation solenoid
FRJM
Alignment motor rear
FSHC
Shutter open/close clutch
FSM
Staple shift motor
FSWM
Oscillation motor
FTLM1
Tray 1 lift motor
FTLM2
Tray 2 lift motor
PDCF
Paper pass cooling fan
PDPGS
Paper pass paper gate solenoid
PDPTM
Paper pass paper transport motor
FPNM
Punch motor
FPSM
Punch horizontal resist motor
FPPM
Saddle paper positioning motor
FS1DFS
Paper deflection plate 1 solenoid
FS2DFS
Paper deflection plate 2 solenoid
FSFCS
Transport plate contact solenoid
FSFM
Saddle transport motor
FSFOM
Paper folding motor
FSFS
Saddle flapper solenoid
FSFSTM
Stitch motor front
FSGM
Guide motor
FSIFM
Saddle entry port transport motor
FSJM
Saddle alignment motor
FSLGM
Paper holding motor
FSRSTM
Stitch motor rear
Item/Display
Content
Setting
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 - 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 - 18
10
C
STAPLE REAR
Staple binding position
adjustment
(one position at the rear)
adjustment
(one position at the rear)
68 - 132
100
D
STAPLE
FRONT
FRONT
Staple binding position
adjustment
(one position in front)
adjustment
(one position in front)
68 - 132
100
E
STAPLE BOTH
Staple binding position
adjustment (center position
of two positions binding)
adjustment (center position
of two positions binding)
68 - 132
100
F
STAPLE PITCH
Staple binding position
adjustment (staple pitch of
two positions binding)
adjustment (staple pitch of
two positions binding)
68 - 132
100
G
PUNCH
CENTER
CENTER
Punch center positioning
sensor
sensor
37 - 63
50
H
PUNCH HOLE
Punch hole adjustment
(paper transport direction)
(paper transport direction)
42 - 58
50
Item/Display
Content
Setting
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle stitch position
adjustment
adjustment
25 - 75
50
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
25 - 75
50
C
FRONT
ADJUST
ADJUST
Paper alignment position
adjustment (Front)
adjustment (Front)
35 - 65
50
D
REAR ADJUST
Paper alignment position
adjustment (Rear)
adjustment (Rear)
35 - 65
50
E
STAPLE REAR
Staple binding position
adjustment (one position at
the rear) (When the paper
width is greater than
232mm)
adjustment (one position at
the rear) (When the paper
width is greater than
232mm)
25 - 75
50
F
STAPLE REAR
R
R
Staple binding position
adjustment (one position at
the rear) (When the paper
width is 232mm or less)
adjustment (one position at
the rear) (When the paper
width is 232mm or less)
45 - 75
50
G
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position in
front) (When the paper
width is greater than
232mm)
adjustment (one position in
front) (When the paper
width is greater than
232mm)
25 - 75
50
H
STAPLE
FRONT R
FRONT R
Staple binding position
adjustment (one position in
front) (When the paper
width is 232mm or less)
adjustment (one position in
front) (When the paper
width is 232mm or less)
25 - 55
50
I
STAPLE BOTH
Staple binding position
adjustment (two positions
at the center)
adjustment (two positions
at the center)
45 - 55
50
J
STAPLE PITCH
Staple binding position
adjustment (two positions
in pitch)
adjustment (two positions
in pitch)
35 - 62
50
K
PUNCH
CENTER
CENTER
Punch center adjustment
35 - 65
50
L
PUNCH HOLE
Punch hole position
adjustment
adjustment
30 - 60
50
M
SADDLE_ADJU
ST_POS
ST_POS
Saddle alignment position
adjustment
adjustment
35 - 65
50
N
GRIPPER_POS
Gripper exit position
adjustment
adjustment
35 - 65
50
Item
Display
Item
Set range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B
STAPLE REAR
Staple binding
position adjustment
(one position at the
rear)
position adjustment
(one position at the
rear)
94 - 106
100
C
STAPLE FRONT
Staple binding
position adjustment
(one position in front)
position adjustment
(one position in front)
94 - 106
100
D
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
30 - 70
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
Item
Display
Item
Set range
Default
value
A
SADDLE
POSITION
POSITION
Saddle stitch position
adjustment
adjustment
197 - 203
200
B
FOLDING
POSITION
POSITION
Saddle folding
position adjustment
position adjustment
192 - 208
200
C
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
Item/Display
Content
Setting
range
Default
value
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.