MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual)

Model
MX-M364N MX-565N (serv.man4)
Pages
127
Size
88.65 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Service Manual (Revised January 2016).
File
mx-m364n-mx-565n-sm4.pdf
Date

View Sharp MX-M364N / MX-565N (serv.man4) Service Manual online

SERVICE MANUAL
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
NOTE FOR SERVICING
[1]
PRODUCT OUTLINE . . . . . . . . . . . . 1-1
[2]
CONSUMABLE PARTS  . . . . . . . . . . 2-1
[3]
EXTERNAL VIEW AND 
INTERNAL STRUCTURE . . . . . . . . . 3-1
[4]
ADJUSTMENTS AND 
SETTINGS  . . . . . . . . . . . . . . . . . . . . 4-1
[5]
SIMULATION  . . . . . . . . . . . . . . . . . . 5-1
[6]
SELF DIAG AND 
TROUBLE CODE . . . . . . . . . . . . . . . 6-1
[7]
FIRMWARE UPDATE . . . . . . . . . . . . 7-1
[8]
MAINTENANCE . . . . . . . . . . . . . . . . 8-1
[9]
VARIOUS STORAGE DATA 
HANDLING . . . . . . . . . . . . . . . . . . . . 9-1
[10] SERVICE WEB PAGE  . . . . . . . . . . 10-1
[11] SPECIFICATIONS  . . . . . . . . . . . . . 11-1
[12] ELECTRICAL SECTION. . . . . . . . . 12-1
[13] TOOL LIST . . . . . . . . . . . . . . . . . . . 13-1
 DETAILS OF EACH SECTION
[A]
EXTERIOR . . . . . . . . . . . . . . . . . . . .A-1
[B]
OPERATION PANEL  . . . . . . . . . . . .B-1
[C]
DSPF/RSPF SECTION. . . . . . . . . .  C-1
[D]
SCANNER SECTION . . . . . . . . . . .  D-1
[E]
PAPER FEED SECTION  . . . . . . . . .E-1
[F]
PAPER TRANSPORT 
SECTION  . . . . . . . . . . . . . . . . . . . . .F-1
[G] LSU SECTION  . . . . . . . . . . . . . . . .  G-1
[H]
PHOTO-CONDUCTOR 
SECTION  . . . . . . . . . . . . . . . . . . . .  H-1
[i]
TONER SUPPLY SECTION . . . . . . .  i-1
[J]
DEVELOPING SECTION . . . . . . . . . J-1
[K]
TRANSFER SECTION . . . . . . . . . . .K-1
[L]
FUSING SECTION . . . . . . . . . . . . . . L-1
[M] DUPLEX/PAPER EXIT 
SECTION  . . . . . . . . . . . . . . . . . . . .  M-1
[N]
DRIVE SECTION  . . . . . . . . . . . . . .  N-1
[O] PWB SECTION. . . . . . . . . . . . . . . .  O-1
[P]
FAN SECTION  . . . . . . . . . . . . . . . . .P-1
[Q] SENSOR/SWITCH SECTION  . . . .  Q-1
TopPage
CONTENTS
CODE: 00ZMXM565/S3E
DIGITAL MULTIFUNCTIONAL SYSTEM
MX-M365N/M364N
MX-M465N/M464N
MX-M565N/M564N
MX-M465N A/M565N A
MX-M564N A
AR-M460N/M560N
AR-M460N X
MODEL
1
: ‘14/Jun
2
: ‘16/Jan
1
2
CONTENTS
NOTE FOR SERVICING
1. Precautions for servicing . . . . . . . . . . . . . . . . . . . . . . . . . i
2. Warning for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
3. Note for installing site. . . . . . . . . . . . . . . . . . . . . . . . . . . . i
4. Note for handling PWB and electronic parts  . . . . . . . . . .ii
5. Note for repairing/replacing the LSU . . . . . . . . . . . . . . .  iii
6. Note for handling the drum unit, the transfer unit, 
the developing unit, and the fusing unit . . . . . . . . . . . . .  iii
7. Screw tightening torque . . . . . . . . . . . . . . . . . . . . . . . . .  iii
[1]
PRODUCT OUTLINE
1. System configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. Machine configuration . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
3. Combination of options  . . . . . . . . . . . . . . . . . . . . . . . . 1-4
[2]
CONSUMABLE PARTS
1. Supply system table. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2. Maintenance parts list  . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
3. Production number identification . . . . . . . . . . . . . . . . . 2-4
[3]
EXTERNAL VIEW AND INTERNAL STRUCTURE
1. Identification of each section and functions . . . . . . . . . 3-1
[4]
ADJUSTMENTS AND SETTINGS
1. General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
2. Adjustment item list . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
3. Details of adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
[5]
SIMULATION
1. General (Including basic operations) . . . . . . . . . . . . . . 5-1
2. List of simulation codes . . . . . . . . . . . . . . . . . . . . . . . . 5-3
3. Details of simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
[6]
SELF DIAG AND TROUBLE CODE
1. Self diag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. Trouble code list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
3. Details of trouble code . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
4. Paper JAM code  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
[7]
FIRMWARE UPDATE
1. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
2. Update procedure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[8]
MAINTENANCE
1. Necessary execution items in maintenance and 
servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
2. Contents of the maintenance codes 
(Relationship between various counters values and 
display messages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
3. Maintenance list (parts) and details of works . . . . . . . . 8-3
[9]
VARIOUS STORAGE DATA HANDLING
1. HDD/SD card/CF card partition and data contents  . . . 9-1
2. Necessary works when replacing the PWB and 
the HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
3. Necessary procedure and notes for replacement of the 
mirroring kit HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
[10] SERVICE WEB PAGE
1. General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
2. Details and operation procedures  . . . . . . . . . . . . . . . 10-1
[11] SPECIFICATIONS
1. Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[12] ELECTRICAL SECTION
1. Block diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
2. Actual wiring chart . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12
3. Signal list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-29
[13] TOOL LIST
1. Exclusive-use tools list. . . . . . . . . . . . . . . . . . . . . . . . 13-1
 DETAILS OF EACH SECTION
[A]
EXTERIOR
1. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .A-1
[B]
OPERATION PANEL
1. Electrical and mechanical relation diagram . . . . . . . . .B-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . .B-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .B-3
[C]
DSPF/RSPF SECTION
1. Electrical and mechanical relation diagram . . . . . . . .  C-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . .  C-6
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  C-6
[D]
SCANNER SECTION
1. Electrical and mechanical relation diagram . . . . . . . .  D-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . .  D-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  D-3
[E]
PAPER FEED SECTION
1. Electrical and mechanical relation diagram . . . . . . . . .E-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . .E-3
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .E-4
[F]
PAPER TRANSPORT SECTION
1. Electrical and mechanical relation diagram . . . . . . . . .F-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . .F-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .F-2
[G]
LSU SECTION
1. Electrical and mechanical relation diagram . . . . . . . .  G-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . .  G-1
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  G-2
[H]
PHOTO-CONDUCTOR SECTION
1. Electrical and mechanical relation diagram . . . . . . . .  H-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . .  H-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  H-3
[i]
TONER SUPPLY SECTION
1. Electrical and mechanical relation diagram . . . . . . . . .  i-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . .  i-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .  i-2
[J]
DEVELOPING SECTION
1. Electrical and mechanical relation diagram . . . . . . . . . J-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . . J-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . . J-2
[K]
TRANSFER SECTION
1. Electrical and mechanical relation diagram . . . . . . . . .K-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . .K-2
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .K-2
[L]
FUSING SECTION
1. Electrical and mechanical relation diagram . . . . . . . . . L-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . . . L-3
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . . L-4
[M]
DUPLEX/PAPER EXIT SECTION
1. Electrical and mechanical relation diagram . . . . . . . .  M-1
2. Operational descriptions  . . . . . . . . . . . . . . . . . . . . . .  M-3
3. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  M-3
[N]
DRIVE SECTION
1. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  N-1
[O]
PWB SECTION
1. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  O-1
[P]
FAN SECTION
1. Disassembly and assembly . . . . . . . . . . . . . . . . . . . . .P-1
[Q]
SENSOR/SWITCH SECTION
1. Disassembly and assembly . . . . . . . . . . . . . . . . . . . .  Q-1
MX-M565N NOTE FOR SERVICING - i
MX-M503N
Service Manual
 
NOTE FOR SERVICING
1.
Precautions for servicing
1)
When servicing, disconnect the power plug, the printer cable,
the network cable, and the telephone line from the machine,
except when performing the communication test, etc.
It may cause an injury or an electric shock.
2)
There is a high temperature area inside the machine. Use an
extreme care when servicing.
It may cause a burn.
3)
There is a high voltage section inside the machine which may
cause an electric shock. Be careful when servicing.
4)
Do not disassemble the laser unit. Do not insert a reflective
material such as a screwdriver in the laser beam path.
It may damage eyes by reflection of laser beams.
5)
When servicing with the machine operating, be careful not to
squeeze you hands by the chain, the belt, the gear, and other
driving sections.
6)
Do not leave the machine with the cabinet disassembled.
Do not allow any person other than a serviceman to touch
inside the machine. It may cause an electric shock, a burn, or
an injury.
7)
When servicing, do not breathe toner, developer, and ink
excessively. Do not get them in the eyes.
If toner, developer, or ink enters your eyes, wash it away with
water immediately, and consult a doctor if necessary.
8)
The machine has got sharp edges inside. Be careful not to
damage fingers when servicing.
9)
Do not throw toner or a toner cartridge in a fire. Otherwise,
toner may explode and burn you.
10) When replacing the lithium battery on the PWB, used the spec-
ified battery only.
If a battery of different specification is used, the battery may
cause malfunction or breakdown of the machine.
11) When carrying a unit with PWB or electronic parts installed on
it, be sure to put it in an anti-static-electricity bag.
It may cause a breakdown or malfunctions.
2.
Warning for servicing
1)
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Avoid complex wiring, which may lead to a fire or an electric
shock.
It may cause a fire or an electric shock.
2)
If there is any abnormality such as smoke or an abnormal
smell, interrupt the job and disconnect the power plug.
It may cause a fire or an electric shock.
3)
Be sure to connect the grounding wire. If an electric leakage
occurs without grounding, a fire or an electric shock may
result.
To protect the machine and the power unit from lightening,
grounding must be made.
4)
When connecting the grounding wire, never connect it to the
following points.
It may cause an explosion, a fire or an electric shock.
* Gas tube
* Lightning conductor
* A water pipe or a water faucet, which is not recognized as a
grounding object by the authorities.
* Grounding wire for telephone line
5)
Do not damage, break, or stress the power cord.
Do not put heavy objects on the power cable. Do not forcibly
bend, pull, or strain the power cord.
It may cause a fire or an electric shock.
6)
Keep the power cable away from a heat source.
Do not insert the power plug with dust on it into a power outlet.
It may cause a fire or an electric shock.
7)
Do not put a metallic object or a container with water in it inside
the machine.
It may cause a fire or an electric shock.
8)
Do not perform servicing, touch the power plug, insert a tele-
phone jack, or operate the machine with wet or only hands.
3.
Note for installing site
Do not install the machine at the following sites.
1)
Place of high temperature, high humidity, low tempera-
ture, low humidity, place under an extreme change in tem-
perature and humidity.
Paper may get damp and form moisture inside the machine,
causing paper jam or copy dirt.
For operating and storing conditions, refer to the specifications
described future in the Service Manual.
2)
Place of much vibration
It may cause a breakdown.
3)
Poorly ventilated place
An electrostatic type copier will produce ozone inside it.
The quantity of ozone produced is designed to a low level so
as not to affect human bodies. However, continuous use of
such a machine may produce an odor of ozone. Install the
machine in a well ventilated place strike, and ventilate occa-
sionally.
CAUTION
DOUBLE POLE/NEUTRAL FUSING
(200V series only)
MX-M565N NOTE FOR SERVICING - ii
4)
Place of direct sunlight.
Plastic parts and toner may be deformed, discolored, or may
undergo qualitative change.
It may cause a breakdown or copy quality issues.
5)
Place which is full of organic gases such as ammonium
The organic photo-conductor (OPC) drum used in the machine
may undergo qualitative change due to organic gases such as
ammonium.
Installation of this machine near a diazo-type copier may result
in copy quality issues.
6)
Place of much dust
When dusts enter the machine, it may cause a breakdown or
copy quality issues.
7)
Place near a wall
Some machines require intake and exhaust of air.
If intake and exhaust of air are not properly performed, copy
dirt or a breakdown may be result.
8)
Unstable or slant surface
If the machine drops or fall down, it may cause an injury or a
breakdown.
If there are optional paper desks and the copier desks speci-
fied, it is recommendable to use them.
When using the optional desk, be sure to fix the adjuster and
lock the casters.
4.
Note for handling PWB and electronic 
parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
1)
When in transit or storing, put the parts in an anti-static bag or
an anti-static case and do not touch them with bare hands.
2)
When and after removing the parts from an anti-static bag
(case), use an earth band as shown below:
* Put an earth band to your arm, and connect it to the
machine.
* When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
11-13/16" 
(30cm)
11-13/16" 
(30cm)
17-23/32" 
(45cm)
MX-M565N NOTE FOR SERVICING - iii
5.
Note for repairing/replacing the LSU
When repairing or replacing, be sure to observe the following
items.
1)
When repairing or replacing the LSU, be sure to disconnect
the power plug from the power outlet.
2)
When repairing or replacing the LSU, follow the procedures
described in this Service Manual.
3)
When checking the operations after repairing the LSU, keep all
the parts including the cover installed and perform the opera-
tion check.
4)
Do not modify the LSU.
5)
When visually checking the inside of the machine for the oper-
ation check, be careful not to allow laser beams to enter the
eyes.
If the above precaution is neglected or an undesignated work is
performed, safety may not be assured.
6.
Note for handling the drum unit, the 
transfer unit, the developing unit, and the 
fusing unit
When handling the OPC drum unit, the transfer unit, and the devel-
oping unit, strictly observe the following items.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
(Drum unit)
1)
Avoid working at a place with strong lights.
2)
Do not expose the OPC drum to lights including interior lights
for a long time.
3)
When the OPC drum is removed from the machine, cover it
with light blocking material. (When using paper, use about 10
sheets of paper to cover it.)
4)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the OPC drum surface.
(Transfer unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the transfer roller.
(Developing unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the developing unit.
(Fusing unit)
1)
Be careful not to put fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
2)
Do not leave the fusing roller in contact state for a long time.
7.
Screw tightening torque
The screws used in this machine are largely classified into three
kinds.
These kinds are classified according to the shape of the screw
grooves and use positions.
The table below shows the kinds of the screws and the tightening
torques depending on the use position.
When tightening the screws for repair or maintenance, refer to the
table.
However, for the other conditions of tightening screws than speci-
fied on this table, or when a special care is required, the details are
described on the separate page. Refer to the descriptions on such
a case.
NOTE: Especially for the screw fixing positions where there is an
electrode or a current flows, use enough care to tighten
securely to avoid loosening.
Screw kinds and tightening torques
Normal screws, set screws (including step screws)
Tapping screws (for iron)
Tapping screw (for plastic)
Screw 
diameter
Material to be 
fixed
Tightening 
torque 
(N
m)
Tightening 
torque 
(kgf
cm)
Tightening 
torque 
(lbft)
M2.6
Steel plate
0.8 - 1.0
8 - 10
0.6 - 0.7
M3
Steel plate
1.0 - 1.2
10 - 12
0.7 - 0.9
M4
Steel plate
1.6 - 1.8
16 - 18
1.2 - 1.3
Screw 
diameter
Material to be 
fixed
Tightening 
torque 
(N
m)
Tightening 
torque 
(kgf
cm)
Tightening 
torque 
(lbft)
M3
Steel plate 
(Plate thickness 
0.8mm or above)
1.0 - 1.2
10 - 12
0.7 - 0.9
M4
Steel plate 
(Plate thickness 
0.8mm or above)
1.6 - 1.8
16 - 18
1.2 - 1.3
M3
Steel plate 
(Plate thickness 
less than 0.8mm)
0.6 - 0.8
6 - 8
0.4 - 0.6
M4
Steel plate 
(Plate thickness 
less than 0.8mm)
1.2 - 1.4
12 - 14
0.9 - 1.0
Screw 
diameter
Material to be 
fixed
Tightening 
torque 
(N
m)
Tightening 
torque 
(kgf
cm)
Tightening 
torque 
(lbft)
M3
Plastic resin
0.6 - 0.8
6 - 8
0.4 - 0.6
M4
Plastic resin
1.0 - 1.2
10 - 12
0.7 - 0.9
MX-M565N  PRODUCT OUTLINE  1 – 1
MX-M503N
Service Manual
 
[1] PRODUCT OUTLINE
1. System diagram
A. MX-M365N/M465N/M565N series
MX-M365N
MX-M465N
MX-M565N
DIGITAL
MULTIFUNCTIONAL SYSTEM
MX-DE12
STAND/1x500 SHEET
PAPER DRAWER
MX-DE13
STAND/2x500 SHEET
PAPER DRAWER
MX-DE14
STAND/3x500 SHEET
PAPER DRAWER
MX-FN17
FINISHER
MX-RB22
PAPER PASS UNIT
MX-LC11
LARGE CAPACITY TRAY
MX-PN11A/B/C/D
PUNCH MODULE
MX-TU12
EXIT TRAY CABINET
MX-TR13 N
EXIT TRAY UNIT
MX-LT10
LONG PAPER FEEDING
TRAY
MX-DE20
STAND/500&2000 SHEET
PAPER DRAWER
MX-PC12
MX-XB16
PLASMACLUSTER ION  
GENERATOR 
MOUNTING KIT 
MX-USX1
SHARPDESK 1 LICENSE
KIT
MX-USX5
SHARPDESK 5 LICENSE
KIT
MX-US10
SHARPDESK 10 LICENSE
KIT
MX-US50
SHARPDESK 50 LICENSE
KIT
MX-USA0
SHARPDESK 100 LICENSE
KIT
MX-UN01A
Sharp OSA Net work Scanner 
Tool 1 License Kit 
MX-UN10A
Sharp OSA Net work Scanner 
Tool 10 License Kit 
MX-UN05A
Sharp OSA Net work Scanner 
Tool 5 License Kit 
MX-UN50A
Sharp OSA Net work Scanner 
Tool 50 License Kit 
MX-UN1HA
Sharp OSA Net work Scanner 
Tool 100 License Kit 
MX-FWX1
INTERNET FAX
EXPANSION KIT
MX-AMX1
APPLICATION
INTEGRATION MODULE
MX-AMX2
APPLICATION
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MX-PUX1
XPS EXPANSION KIT
MX-PF10
BARCODE FONT KIT
AR-SU1
STAMP UNIT
MX-FX11
FACSIMILE EXPANSION
KIT
MX-FR44U/FR44
DATA SECURITY KIT
MX-FR44U/FR
DATA SECURITY KIT
MX-EB11
ENHANCED COMPRESSION
KIT
MX-EB12 N 
MIRRORING KIT
MX-AM10
WEB BROWSING EXPANSION
KIT
MX-KB11 N 
KEYBOARD
MX-FN10
SADDLE STITCH FINISHER
MX-PNX5A/B/C/D
PUNCH MODULE
MX-PNX6A/B/C/D
PUNCH MODULE
MX-FN18
SADDLE STITCH FINISHER
MX-FN11
FINISHER
MX-M565N  PRODUCT OUTLINE  1 – 2
B. MX-M364N/M464N/M564N series
MX-M364N
MX-M464N
MX-M564N
DIGITAL
MULTIFUNCTIONAL SYSTEM
MX-DE12
STAND/1x500 SHEET
PAPER DRAWER
MX-DE13
STAND/2x500 SHEET
PAPER DRAWER
MX-DE14
STAND/3x500 SHEET
PAPER DRAWER
MX-FN17
FINISHER
MX-RB22
PAPER PASS UNIT
MX-LC11
LARGE CAPACITY TRAY
MX-PN11A/B/C/D
PUNCH MODULE
MX-TU12
EXIT TRAY CABINET
MX-TR13 N
EXIT TRAY UNIT
MX-LT10
LONG PAPER FEEDING
TRAY
MX-DE20
STAND/500&2000 SHEET
PAPER DRAWER
MX-PC12
MX-XB16
PLASMACLUSTER ION  
GENERATOR 
MOUNTING KIT 
MX-US10
SHARPDESK 10 LICENSE
KIT
MX-US50
SHARPDESK 50 LICENSE
KIT
MX-USA0
SHARPDESK 100 LICENSE
KIT
MX-UN01A
Sharp OSA Network Scanner
Tool 1 License Kit
MX-UN05A
Sharp OSA Network Scanner
Tool 5 License Kit
MX-UN10A
Sharp OSA Net work Scanner 
Tool 10 License Kit 
MX-UN1HA
Sharp OSA Net work Scanner 
Tool 100 License Kit 
MX-UN50A
Sharp OSA Net work Scanner 
Tool 50 License Kit 
MX-FWX1
INTERNET FAX
EXPANSION KIT
MX-AMX2
APPLICATION
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MX-USX1
SHARPDESK 1 LICENSE
KIT
MX-PUX1
XPS EXPANSION KIT
MX-PF10
BARCODE FONT KIT
AR-SU1
STAMP UNIT
MX-FX11
FACSIMILE EXPANSION
KIT
MX-FR45U
DATA SECURITY KIT
DATA SECURITY KIT
MX-KB14 N 
KEYBOARD
MX-FN10
SADDLE STITCH FINISHER
MX-PNX5A/B/C/D
PUNCH MODULE
MX-PNX6A/B/C/D
PUNCH MODULE
MX-FN18
SADDLE STITCH FINISHER
MX-FN11
FINISHER
MX-EB13
USB WIRELESS LAN ADAPTER
MX-PK11
PS3 EXPANSION KIT 
MX-AMX1
APPLICATION
INTEGRATION MODULE
MX-USX5
SHARPDESK 5 LICENSE
KIT
TopPage
MX-M565N  PRODUCT OUTLINE  1 – 3
C. AR-M460N/M560N series
2. Machine configuration
STD: Standard provision.  OPT: Option.   N/A: Not available.   *1: No support in some region.   *2: Option in some region.
MX-M365N / M465N
MX-M465N A / M565N A
MX-M565N
MX-M364N/M464N/M564N
MX-M564N A
AR-M460N/M560N
AR-M460N X
Copy
STD
PCL printer
STD
PS printer
STD
OPT
N / A
Main body LCD
COLOR WSVGA 10.1"
COLOR WSVGA 7.0"
FAX
OPT*1
N / A
Scan
STD
Document Feeder
STD DSPF
STD RSPF
Exit Tray Cabinet
STD/OPT *2
STD
Sharp OSA
STD
OPT
N / A
Key Board
STD / OPT*2
OPT
N / A
Web Browsing
OPT
STD / OPT*2
N / A
N / A
Wireless LAN
STD*1
OPT*1
HDD (GB)
320
N / A
AR-M460N
AR-M560N
AR-M460N X
DIGITAL
MULTIFUNCTIONAL SYSTEM
MX-DE12
STAND/1x500 SHEET
PAPER DRAWER
MX-DE13
STAND/2x500 SHEET
PAPER DRAWER
MX-DE14
STAND/3x500 SHEET
PAPER DRAWER
MX-FN17
FINISHER
MX-RB22
PAPER PASS UNIT
MX-LC11
LARGE CAPACITY TRAY
MX-PN11A/B/C/D
PUNCH MODULE
MX-LT10
LONG PAPER FEEDING
TRAY
MX-DE20
STAND/500&2000 SHEET
PAPER DRAWER
AR-SU1
STAMP UNIT
MX-FN10
SADDLE STITCH FINISHER
MX-PNX5A/B/C/D
PUNCH MODULE
MX-PNX6A/B/C/D
PUNCH MODULE
MX-FN18
SADDLE STITCH FINISHER
MX-FN11
FINISHER
MX-EB13
USB WIRELESS LAN ADAPTER
TopPage
1
: ‘14/Jun
1
2
: ‘16/Jan
2
2
MX-M565N  PRODUCT OUTLINE  1 – 4
3. Combination of options
STD: Standard provision.  OPT: Installable.  ―: Cannot be connected. 
*1: Option in some region. 
*2: No support in some region
Section
Name
Model name
MX-M365N 
MX-M465N
MX-M465N A
MX-M565N A
MX-M565N
MX-M364N
MX-M464N
MX-M564N
MX-M564N A
AR-M460N
AR-M560N
AR-M460N X
Remarks
Document 
Feed System
DUPLEX SINGLE PASS FEEDER
STD
STD
REVERSING SINGLE PASS FEEDER
STD
STD
Paper Feed 
System
STAND/1 x 500 SHEET PAPER DRAWER
MX-DE12
OPT
OPT
OPT
OPT
STAND/2 x 500 SHEET PAPER DRAWER
MX-DE13
OPT
OPT
OPT
OPT
STAND/3 x 500 SHEET PAPER DRAWER
MX-DE14
OPT
OPT
OPT
OPT
STAND/500 & 2000 SHEET PAPER DRAWER
MX-DE20
OPT
OPT
OPT
OPT
LARGE CAPACITY TRAY
MX-LC11
OPT
OPT
OPT
OPT
LONG PAPER FEEDING TRAY
MX-LT10
OPT
OPT
OPT
OPT
Paper Exit 
System
EXIT TRAY UNIT
MX-TR13 N
OPT
OPT
OPT
EXIT TRAY CABINET
MX-TU12
STD/OPT
STD/OPT
STD/OPT
STD
*1
FINISHER
MX-FN17
OPT
OPT
OPT
OPT
PUNCH MODULE
MX-PN11
A/B/C/D
OPT
OPT
OPT
OPT
For MX-
FN17
PAPER PASS UNIT
MX-RB22
OPT
OPT
OPT
OPT
SADDLE STITCH FINISHER
MX-FN10
OPT
OPT
OPT
OPT
FINISHER (4K)
MX-FN11
OPT
OPT
OPT
OPT
SADDLE STITCH FINISHER
MX-FN18
OPT
OPT
OPT
OPT
PUNCH MODULE
MX-PNX5
A/B/C/D
OPT
OPT
OPT
OPT
For MX-
FN10
PUNCH MODULE
MX-PNX6
A/B/C/D
OPT
OPT
OPT
OPT
For MX-
FN11/
FN18
Printer 
Expansion
PS3 EXPANSION
MX-PK11
STD
STD
OPT
BARCODE FONT KIT
MX-PF10
OPT
OPT
OPT
XPS EXPANSION KIT
MX-PUX1
OPT
OPT
OPT
Image send 
expansion
FACSIMILE EXPANSION KIT
MX-FX11
OPT
OPT
OPT
*2
STAMP UNIT
AR-SU1
OPT
OPT
OPT
OPT
INTERNET FAX EXPANSION KIT
MX-FWX
OPT
OPT
OPT
ENHANCED COMPRESSION KIT
MX-EB11
OPT
OPT
Authentication 
/ Security
DATA SECURITY KIT
MX-FR44U
OPT
OPT
DATA SECURITY KIT
MX-FR45U
OPT
CARD COLUTION KIT
MX-EC50
OPT
OPT
*2
MIRRORING KIT
MX-EB12 N
OPT
OPT
Application /
Solution
SHARPDESK 1 LICENSE KIT
MX-USX1
OPT
OPT
OPT
SHARPDESK 5 LICENSE KIT
MX-USX5
OPT
OPT
OPT
SHARPDESK 10 LICENSE KIT
MX-US10
OPT
OPT
OPT
SHARPDESK 50 LICENSE KIT
MX-US50
OPT
OPT
OPT
SHARPDESK 100 LICENSE KIT
MX-USA0
OPT
OPT
OPT
SHARP OSA NETWORK SCANNER TOOL 1 
LICENSE KIT
MX-UN01A
OPT
OPT
OPT
SHARP OSA NETWORK SCANNER TOOL 5 
LICENSE KIT
MX-UN05A
OPT
OPT
OPT
SHARP OSA NETWORK SCANNER TOOL 10 
LICENSE KIT
MX-UN10A
OPT
OPT
OPT
SHARP OSA NETWORK SCANNER TOOL 50 
LICENSE KIT
MX-UN50A
OPT
OPT
OPT
SHARP OSA NETWORK SCANNER TOOL 
100 LICENSE KIT
MX-UN1HA
OPT
OPT
OPT
APPLICATION INTEGRATION MODULE
MX-AMX1
OPT
OPT
OPT
APPLICATION COMMUNICATION MODULE
MX-AMX2
STD/OPT
STD/OPT
OPT
*1
EXTERNAL ACCOUNT MODULE
MX-AMX3
STD/OPT
STD/OPT
OPT
*1
WEB BROWSING EXPANSION KIT
MX-AM10
OPT
STD/OPT
*1
OTHER
KEYBOARD
MX-KB11 N
STD/OPT
STD/OPT
*1
KEYBOARD
MX-KB14 N
OPT
USB WIRELESS LAN ADAPTER
MX-EB13
OPT
OPT
*2
PLASMACLUSTER ION GENARATOR
MX-PC12
OPT
OPT
OPT
*2
PLASMACLUSTER ION GENERATOR 
MOUNTING KIT
MX-XB16
OPT
OPT
OPT
*2
1
1
: ‘14/Jun
2
: ‘16/Jan
2
MX-M565N  CONSUMABLE PARTS  2 – 1
MX-M503N
Service Manual
 
[2] CONSUMABLE PARTS
1. Supply system table
A. USA/Canada/South and Central America
B. Europe/Australia/New Zealand/Korea
C. Asia/Hong Kong
D. Middle East/Africa/Israel/Philippines/Taiwan
E. China
No.
Item
Content
Life
Model Name
Quantity in 
collective 
package
Remarks
1
Toner Cartridge (Black)
Toner Cartridge
x 1
40K
MX-560NT
10
Life: A4/Letter 
6% document
2
Developer (Black)
Developer
x 1
600K
MX-560NV
10
3
Drum
OPC  Drum
x  1
300K
MX-560DR
10
No.
Item
Content
Life
Model Name
Quantity in 
collective 
package
Remarks
1
Toner Cartridge (Black)
Toner Cartridge
x 1
40K
MX-560GT
10
Life: A4/Letter 
6% document
2
Developer (Black)
Developer
x 1
600K
MX-560GV
10
3
Drum
OPC Drum
x 1
300K
MX-560DR
10
No.
Item
Content
Life
Model Name
Quantity in 
collective 
package
Remarks
1
Toner Cartridge (Black)
Toner Cartridge
x 1
40K
MX-560AT
10
Life: A4/Letter 
6% document
2
Developer (Black)
Developer
x 1
600K
MX-560AV
10
3
Drum
OPC Drum
x 1
300K
MX-560DR
10
No.
Item
Content
Life
Model Name
Quantity in 
collective 
package
Remarks
1
Toner Cartridge (Black)
Toner Cartridge
x 1
40K
MX-560FT
10
Life: A4/Letter 
6% document
2
Developer (Black)
Developer
x 1
600K
MX-560FV
10
3
Drum
OPC Drum
x 1
300K
MX-560DR
10
No.
Item
Content
Life
Model Name
Quantity in 
collective 
package
Remarks
1
Toner Cartridge (Black)
Toner Cartridge
x 1
40K
MX-560CT
10
Life: A4/Letter 
6% document
2
Developer (Black)
Developer
x 1
600K
MX-560CV
10
3
Drum
OPC Drum
x 1
300K
MX-560DR
10

Download Sharp MX-M364N / MX-565N (serv.man4) Service Manual (Repair Manual)

Here you can view online and download Sharp MX-M364N / MX-565N (serv.man4) Service Manual in PDF. MX-M364N / MX-565N (serv.man4) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp MX-M364N / MX-565N (serv.man4) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.