Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N SIMULATION 5 – 13
6-90
Purpose
Setting
Function (Purpose)
Reset the machine to the factory setting.
(The scanner is set to the lock enable posi-
tion).
(The scanner is set to the lock enable posi-
tion).
Section
Scanner
Operation/Procedure
1)
Press [EXECUTE] key.
The scanner is shifted to the lock enable position and stopped.
7
7-1
Purpose
Setting
Function (Purpose)
Set the operating conditions of aging.
Section
Operation/Procedure
1)
Select the target to be set with the touch panel key.
2)
Press [EXECUTE] key.
The machine is rebooted in the aging mode.
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
after unless the power is turned off or the setting is changed.
7-6
Purpose
Setting
Function (Purpose)
Set the operating intermittent aging cycle.
Section
Operation/Procedure
1)
Enter the intermittent aging operation cycle (unit: sec) with 10-
key.
key.
2)
Press [OK] key.
The time entered in procedure 1) is set.
* The interval time that can be set is 1 to 900 (sec).
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
after unless the power is turned off or the setting is changed.
7-8
Purpose
Information display/print
Function (Purpose)
Display the warm-up time.
Section
Fusing
Operation/Procedure
Press [EXECUTE] key.
Counting of the warm-up time is started and the time required for
warm-up is displayed
warm-up is displayed
* Interruption of counting by pressing [EXECUTE] key is inhibited.
7-12
Purpose
Operation test/check
Function (Purpose)
The document reading number of sheets
setting (for aging operation)
setting (for aging operation)
Section
Automatic document feeder
Operation/Procedure
1)
Set document reading quantity with 10-key.
(Setting range: 0 - 255)
(Setting range: 0 - 255)
2)
Press [OK] key. The set value is saved.
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
after unless the power is turned off or the setting is changed.
8
8-1
Purpose
Adjustment
Function (Purpose)
Check and adjust the operations of the
developing voltage in each print mode and
the control circuit.
developing voltage in each print mode and
the control circuit.
Section
Toner supply, developing
Operation/Procedure
1)
Enter the setting value with 10-key.
2)
Press [EXECUTE] key.
The entered voltage is outputted for 30 sec and the set value is
saved. When [EXECUTE] key is pressed during outputting, the
operation is terminated.
saved. When [EXECUTE] key is pressed during outputting, the
operation is terminated.
8-2
Purpose
Adjustment
Function (Purpose)
Check and adjust the operation of the main
charger grid voltage in each printer mode
and the control circuit.
charger grid voltage in each printer mode
and the control circuit.
Section
Photo-conductor
Operation/Procedure
1)
Enter the setting value with 10-key.
2)
Press [EXECUTE] key.
The entered voltage is outputted for 30 sec and the set value is
saved. When [EXECUTE] key is pressed during outputting, the
operation is terminated.
saved. When [EXECUTE] key is pressed during outputting, the
operation is terminated.
AGING
Aging operation setup
INTERVAL
Intermittent setup
MISFEED DISABLE
JAM detection enable/disable setup
FUSING DISABLE
Fusing operation enable/disable setup
WARMUP DISABLE
Warm-up skip setup
DV CHECK DISABLE
DV unit detection enable/disable setup
SHADING DISABLE
Shading disable setup
CCD GAIN FREE
No setting of the CCD gain adjustment
Item/Display
Content
Setting
range
Default
value
MIDDLE
A
Developing bias set value
0-700
475
LOW
A
Developing bias set value
0-700
475
Item/Display
Content
Setting
range
Default value
36
cpm
46/56
cpm
MIDDLE
A
Main charger grid
voltage
voltage
150 -
850
850
645
650
LOW
A
645
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.