DX-C310, DX-C311, DX-C400, DX-C401 (serv.man4). GENERAL PROCEDURE FOR SETUP AND CALIBRATION - Sharp Copying Equipment Handy Guide

dx-c310, dx-c311, dx-c400, dx-c401 (serv.man4) handy guide
Model
DX-C310 DX-C311 DX-C400 DX-C401 (serv.man4)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
200.56 KB
Type
PDF
Document
Handy Guide
Brand
Device
Copying Equipment / GENERAL PROCEDURE FOR SETUP AND CALIBRATION
File
dx-c310-dx-c311-dx-c400-dx-c401-sm4.pdf
Date

Read Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man4) Handy Guide online

 
 
 
Document Solutions After Sales Service
Calibration
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1. Model Name 
MX‐C310 – DX‐C381. 
 
2. Description 
This is a Colour Calibration procedure to allow the MFP to perform at the best level of copy 
quality for the product. The procedure should be followed in order. It is split into three levels, 
black should be performed after every call, black and blue should be performed after a 
preventative maintenance call and black blue and red should be performed if a problem still 
exists. 
 
Black: All call procedure 
Blue: After preventative maintenance 
Red: If there are still problems with CQ 
 
3. Tools Required 
 
SERVICE MANUAL 
INSTALLATION MANUAL
MONDI COLOUR COPY PAPER 
A4 100g/m² 
IMAGE DENSITY SENSOR CALIBRATION JIG 
UKOG‐0318FCZZ 
SHARP COLOUR TEST CHART
UKOG‐0326FCZZ
SIT CHART 
UKOG‐0280FCZ1
SHARP GREY CHART 
UKOG‐0162FCZZ 
 
4. Procedure 
1. Ensure that the MFP is at the latest level of firmware according to Sharp (UK) Technical website 
(SIM 22‐05) 
 
 
2.
 
Ensure all Process Voltages for DV Bias, Main Charge Grid Voltage and Transfer Voltage are set 
to the correct values (ADJ 1)
 
 
 
3. Execute simulation 22‐06 and ensure on page 2 all settings in SIM 46‐01 and SIM 46‐02 are set 
to default 50, also ensure that SIM 46‐10, SIM46‐16 and SIM 46‐21 are default to 500 (If these 
have been adjusted they can be reset after calibration) 
 
 
4. Clean all mirrors, glass, lens, white reference plate and CCD in optics cavity 
 
 
5. Use image density sensor calibration jig and execute SIM 44‐13 as per service manual (ADJ 2a) 
 
 
6. Perform black image density sensor and image registration sensor adjustment by executing 
SIM  44‐02 as per service manual (ADJ 2b) 
 
 
7. Perform black LSU skew adjustment (SIM 61‐04) as per service manual (ADJ 3)
 
 
GENERAL PROCEDURE FOR COLOUR CALIBRATION 
SET‐UP
C Frontier Calibration Set‐Up 
Date:   
2
nd
 December 2008 
Model:  
MX‐C310 – DX‐C381 
Ref.:   
CQ set‐up 
Colour:  
White
 
Page:   
1 of 2 
 
 
 
Document Solutions After Sales Service
Calibration
 
 
8. Perform Drum Phase/Image Registration/Colour Laser Skew adjustment by executing SIM 50‐
22 and selecting ALL (ADJ 4a) 
 
 
9. Execute SIM 44‐27, clearing half tone process control correction values 
 
 
10. Execute SIM 44‐06, forced execution of process control 
 
 
11. Execute SIM 44‐26, forced execution of half tone image correction 
                                                   
                                                  
12. Execute SIM  63‐11 & choose engine DEF1 default target. 
 
                                                  13. Execute SIM  63‐08 to match scanner service target to factory target. 
 
                                                  14. Execute SIM  67‐26  & choose printer DEF1 default target. 
 
                                                  15. Execute SIM 67‐28 to match printer service target to factory target. 
                                           
                                                  
16. Calibrate the CCD array by using the SIT chart and executing SIM 63‐03 (ADJ 14a)
 
 
 
17. Ensure good quality A4 colour copy paper is in the machine and perform Auto Colour 
Calibration by executing SIM 46‐74 (This simulation performs both the engine and printer 
calibration simultaneously).  
 
18. Place the printed colour patch test page (Figure 1) face down on the glass so that the fine 
lines are on the left hand side, then lay 5 sheets of clean A4 paper on top of the test page. 
Select “FACTORY” method when calibrating. The copy colour balance adjustment is 
automatically executed and prints the colour balance check page (Figure 2). Check for defects, 
if OK continue to step 15, if not fault find and rectify. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
19. Select “Execute” again, this time the Printer calibration patch test page (Figure 3) will be 
printed. Place face down on the glass so that the fine lines are on the left hand side, then lay 5 
sheets of clean A4 paper on top of the test page. Select “FACTORY” method when calibrating. 
The copy colour balance adjustment is automatically executed and prints the colour balance 
check page (Figure 4). Check for defects, if OK select OK, if not fault find and rectify. Colour 
calibration is now complete. 
 
 
 
 
 
Figure 1 
Figure 2 
 
 
Figure 3 
Figure 4 
Page of 2
Display

Download Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man4) Handy Guide

Here you can read online and download Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man4) Handy Guide in PDF. DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man4) handy guide will guide through the process and help you recover, restore, fix, disassemble and repair Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man4) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.