MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 105

MX-M565N  SIMULATION  5 – 5

44

6

Execute the high density process control forcibly.

Process

9

Display the result data of the high density process control operation.

Image process

12

Display the operation data of the high density process control and the image density 
sensor.(registration sensor)

Image process

14

Display the output level of the temperature and humidity sensor.

Process

15

Set the OPC drum idle rotation.

Process

17

Process refresh execution

21

Set the halftone process control target.

Process

22

Display the toner patch density level in the half tone process control operation.

Process

24

Display the correction target and the correction level in the half tone process control operation.

Process

25

Set the calculating conditions of the correction value for the half tone process control.

Process

26

Execute the half tone process control compulsory.

Process

27

Clear the correction data of the half tone process control.

Process

28

Set the process control execution conditions.

Process

29

Set the operating conditions of the process control during a job.

Process

34

Set the process control execution conditions.

Process

37

Set the development bias correction level in the continuous printing operation.

Toner supply, developing

43

Display the identification information of the developing unit.

Developing

62

Set the process control execution conditions

Process

46

2

Adjust the copy density in each copy mode.

4

Adjust the density in the image send mode (color mode)

5

Adjust the density in the image send mode (monochrome mode).

8

Adjust the image send mode color balance RGB.

9

Adjust scan image density (copy, image send mode)

10

Adjust the copy density (in each copy mode).

16

Adjust the copy density and gamma.

19

Set the operating conditions of document density scanning (copy, image send mode).

Scanner

23

Set the density correction of copy high density section (High density tone gap supported).

24

Copy half tone adjustment (Auto adjustment)

32

Adjust the document background density reproductivity in the auto copy mode.

37

Adjust the reproduction capability of the scan image color document (copy, image send mode).

39

Adjust the sharpness of FAX send images.

40

Adjust the FAX send image density. (Collective adjustment of all the modes)

41

Adjust the FAX send image density. (Normal)

42

Adjust the FAX send image density. (Fine)

43

Adjust the FAX send image density. (Super Fine)

44

Adjust the FAX send image density. (Ultra fine)

45

Adjust the FAX send image density. (600dpi).

46

Adjust the FAX send image density (RGB RIP)

47

Set the JPEG compression rate in copy and scan images.

48

Set the output resolution in each copy mode.

51

Adjust the gamma for copy, heavy paper mode and image process mode (manual adjustment).

52

Set the gamma default for the copy mode heavy paper and the image process mode. (After 
execution of either SIM46-54 or SIM46-51 the adjustment value is reset to the initial value)

54

Perform the engine halftone automatic density adjustment (dither)

55

Adjust the drop out color in the image send mode (monochrome manual text mode)

58

Set the copy mode pseudo resolution (smoothing process)

59

Perform the copy mode pseudo resolution image process adjustment

60

Adjust the sharpness in the color auto mode

61

Adjust the area separation recognition level in image send mode (color, gray, auto exposure mode).

62

Set the operating conditions of the ACS, the area separation, the background image process, and 
the auto exposure mode.

63

Adjust the density in the copy low density section.

66

Adjust the reproduction capability of watermark in the copy/printer mode.

74

Adjust copy gray balance (Auto adjustment) / printer gray balance (Auto adjustment)

90

Set the process operation of high-compression PDF images.

91

Adjust the reproduction capability of black text.

48

1

Adjust the scan image magnification ratio (main scanning direction and sub scanning direction).

Scanner

5

Correction the scan image magnification ratio (sub scanning direction).

Scanner

6

Adjust the rotation speed of each motor.

49

1

Perform the firmware update.

3

Update the operation manual data stored in the HDD.

5

Update the watermark data stored in the HDD.

10

Perform the ACU firmware update.

50

1

Copy image position, image loss adjustment

5

Adjust the print lead edge image position. (PRINTER MODE)

6

Adjust the copy image position and the image loss (SPF mode).

7

Adjust DSPF document lead edge (simple method) and copy image position on print paper and the 
void area (image loss) in the copy mode.

10

Adjust the image off-center position. 
(The adjustment is made separately for each paper feed section.)