Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N SIMULATION 5 – 3
2. List of simulation codes
Main
Sub
Functions
Section
1
1
Check the operation of the scanner (reading) unit and the control circuit.
Scanner (reading)
2
Check the sensors in the scanner (reading) section and the related circuits.
Scanner
5
Check the operation of the scanner (reading) unit and the control circuit.
Scanner (reading)
2
1
Check the operation of the automatic document feed unit and the control circuit.
Automatic document feeder
2
Check the operation of sensors and detectors in the SPF unit section and the control circuits.
Automatic document feeder
3
Check the operation of the loads in the automatic document feed unit and the control circuit.
Automatic document feeder
3
2
Check the operation of the sensors and the detectors in the finisher and the control circuit.
Finisher
3
Check the operation of the load in the finisher and the control circuit.
Finisher
10
Adjust the finisher.
Finisher
4
2
Check the paper feed section (Desk/LCC) sensors and detectors and their control circuits.
Paper feed, paper reverse/transport
3
Check the paper feed section (Desk/LCC) loads and their control circuits.
Paper feed, paper reverse/transport
5
Check the operation of the paper transport clutch for the paper feed tray unit.
Paper feed, paper reverse/transport
5
1
Check the operation of the display, LCD in the operation panel, and control circuit.
Operation unit (Operation/Display PWB)
2
Check the operation of the heater lamp and the control circuit.
Fusing
3
Check the operation of the scanner lamp and the control circuit.
Scanner (reading)
4
Check the operation of discharge lamp and the control circuit.
Process
6
1
Check the operation of load in paper transport system (clutches, solenoids) and control circuits.
Paper feed, paper reverse/transport
2
Check the operations of each fan and its control circuit.
Others
90
Reset the machine to the factory setting. (The scanner is set to the lock enable position)
Scanner
7
1
Set the operating conditions of aging.
6
Set the operating intermittent aging cycle.
8
Display the warm-up time.
Fusing
12
The document reading number of sheets setting (for aging operation)
Automatic document feeder
8
1
Check/Adjust the operation of the developing voltage in each print mode and control circuit.
Toner supply, developing
2
Check/Adjust the operation of the main charger grid voltage in each printer mode and control circuit.
Photo-conductor
6
Check/Adjust the operation of the transport voltage and the control circuit.
Transfer
17
Check/Adjust the operation of the separation bias voltage and the control circuit.
9
2
Check the operation of sensors and detectors in the duplex section and its control circuit.
Paper feed, paper reverse/transport
3
Check the operation of the load in the paper reverse section (duplex section) and its control circuit.
Duplex
10
1
Check the operation of the toner supply mechanism (toner clutch) and the related circuit.
Toner supply, developing
13
-
Cancel the self diag "U1" trouble.
MFP (ICU) PWB
14
-
Cancel the self diag "H3, H4, H5" trouble.
Fusing
15
-
Cancel the self diag "U6-09" trouble.
LCC
16
-
Cancel the self diag "U2" trouble.
21
1
Set the maintenance cycle.
22
1
Check the print count value in each operation mode.
2
Check the total number of mis-feed and the troubles.(when the number of total jam is considerably
great, it is judged as necessary for repair)
great, it is judged as necessary for repair)
3
Check the mis-feed position and the mis-feed count of each position.
4
Check the trouble (self diag) history.
5
Check the ROM version of each unit (section).
6
Print settings, adjustments data (simulation, FAX soft switch, counters), firmware version, and
counter list.
counter list.
8
Check the number of operations (counter value) of the finisher, the SPF, and scanning (reading).
9
Check the umber of use (print quantity) of each paper feed section.
Paper feed, paper reverse/transport
10
Check the system configuration (options and internal hardware).
11
Check the use frequency of send/receive of FAX. (Only when FAX is installed.)
FAX unit (TEL/LIU, FAX control PWB)
12
Check the DSPF mis-feed position and the number of mis-feed at the position.(when the number of
mis-feed is considerably great, it can be judged as necessary for repair)
mis-feed is considerably great, it can be judged as necessary for repair)
Automatic document feeder
13
Check the use quantity of the process section (OPC drum, DV unit, toner cartridge).and fusing.
Process
14
Display the use status of the toner cartridge
Process
18
Display the user data delete history
19
Check various counter values related to scan - image send.
40
Display the error code list and the contents
42
Check the JAM/trouble data
43
Display JAM data details
90
Output the various set data lists.
23
2
Output the trouble history list of paper jam and mis-feed.
80
Output the operation data of paper feed and paper transport in the paper feed/transport section.
Paper feed, paper reverse/transport
81
Backup the paper feed time data to the USB memory
24
1
Clear the jam counter, and the trouble counter.
2
Clear the number of use (the number of prints) of each paper feed section.
Paper feed, paper reverse/transport
3
Clear the finisher, SPF, and the scan (reading) unit counter.
4
Clear the maintenance counter, the printer counters of the transfer unit and the fusing unit.
5
Clear the developer counter.
Toner supply, developing
6
Clear the copy counter.
9
Clear the printer mode print counter and the self print mode print counter.
10
Clear the FAX counter. (Only when FAX is installed)
FAX unit (TEL/LIU, FAX control PWB)
12
Clear the document filing counter
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.