Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N SIMULATION 5 – 4
24
15
Clear the counters related to the scan mode and the image send.
35
Clear the toner cartridge use status data
25
1
Check the operations of the developing section.
Toner supply, developing
2
Make the initial setting of toner density when replacing developer. (Automatic adjustment)
Image process
4
Display the operation data of the toner supply quantity
Process
26
1
Set the paper exit operation from the right side.
Paper exit section
2
Set the paper size of the large capacity tray (LCC) .
Paper feed
3
Set the specifications of the auditor.
Auditor
5
Set the count mode of the total counter and the maintenance counter (A3/11" x 17" size).
6
Set the specifications (paper, fixed magnification ratio) of the destination.
7
Set the machine ID
8
Counter mode setting for long scale paper size
10
Set the trial mode of the network scanner.
18
Set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.)
30
Set the operation mode corresponding to the CE mark (Europe safety standards).
32
Set the specifications of the fusing cleaning operation
Fusing
35
Set the trouble history display mode.
38
Set "Print continue" or "Print stop" when the maintenance timing is reached or the consumable part
life is over.
life is over.
41
Set Enable/Disable of magnification ratio automatic select function (AMS) in center binding mode.
49
Set the print speed of postcards mode.
50
Set the operation specifications and functions.
51
Set the specifications of the serial port operation
PCI
52
Set whether non-printed paper (insertion paper, cover paper) is counted up or not.
53
Set Inhibit/Allow of the user auto calibration (gradation, density adjustment).
65
Set the limit of the staple process.
69
Set the operating conditions for toner near end.
71
Set the trial mode of the web browsing function
73
Adjust the image loss (shade removal amount) in the poster, the continuous enlargement copy, the
card scan, and the A3 wide copy mode.
card scan, and the A3 wide copy mode.
74
Set the OSA trial mode.
78
Set the password of the remote operation panel mode.
79
Set YES/NO of the pop-up display of user data delete result
27
1
Set non-detection of communication error (U7-00) with RIC. (FSS function)
2
Set the sender's registration number and the HOST server telephone number. (FSS function)
4
Set the initial call and toner order auto send. (FSS function)
5
Set the machine tag No. (FSS function)
6
Set of the manual service call. (FSS function)
7
Set of the enable, alert call out. (FSS function)
9
Set the paper transport time recording YES/NO threshold value and shading gain adjustment retry
number. (FSS function)
number. (FSS function)
10
Clear the trouble prediction history information. (FSS function)
11
Check the serial communication retry number and the scanner gain adjustment retry number
history. (FSS function)
history. (FSS function)
12
Check the high-density and the half-tone process control error history. (FSS Function)
13
Check the history of paper transport time between sensors. (FSS function)
14
Set the FSS function connection test mode.
15
Display the FSS connection status
16
Set the FSS alert send
17
Set the FSS paper order alert
18
Clear the FSS paper feed retry counter
30
1
Check the operation of sensors and detectors in other than paper feed section and control circuits.
Paper feed, paper reverse/transport
2
Check the operations of the sensors and the detectors in the paper feed section and control circuits.
Paper feed, paper reverse/transport
40
2
Manual paper feed tray paper width sensor adjustment.
Paper feed, paper reverse/transport
7
Set the adjustment value of the manual paper feed tray paper width sensor.
Paper feed, paper reverse/transport
41
1
Check the operation of the document size sensor and the control circuit.
Others
2
Adjust the document size sensor detection level.
Others
3
Check the operation of the document size sensor and the control circuit.
Others
43
1
Set the fusing temperature in each operation mode.
Fusing
2
Set the fusing temperature and pre-heat each operation mode.
Fusing
20
Set the environmental correction under low temperature and low humidity (L/L) for the fusing
temperature setting (SIM 43-2) in each paper mode.
temperature setting (SIM 43-2) in each paper mode.
Fusing
21
Set the environment correction under high temperature and high humidity (H/H) for the fusing
temperature setting (SIM 43-2) in each paper mode.
temperature setting (SIM 43-2) in each paper mode.
Fusing
24
Set the fusing operation mode.
Fusing
31
Check the operation of the fusing web cleaning motor.
Fusing
32
Set various items related to the forcible operation of web cleaning when job end.
Fusing
34
Check the fusing lower web cleaning motor operation.
Fusing
35
Check fusing nip operation.
Fusing
44
1
Set each correction operation function in the image forming (process) section.
Image process
2
Adjust the sensitivity of the image density sensor. (registration sensor)
Process
4
Set the conditions of the high density process control operation.
Process
Main
Sub
Functions
Section
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.