Read Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man35) User Guide / Operation Manual online
13
General Problems
Is the original a long original?
■ When using the automatic document feeder to scan a long original, set the scan
size to [Long Size].
(Note that long originals cannot be copied using the copy function.)
Is the original on thin paper?
■ Use the document glass to scan the original.
If you need to use the automatic document feeder, use [Slow Scan Mode] in
[Others] to scan the original.
[Others] to scan the original.
THE PAPER MISFEEDS
Check
Solution
Is a torn piece of paper remaining in
the machine?
the machine?
■ Follow the instructions in the touch panel to remove all paper.
Is too much paper loaded in the tray?
■ Reload the paper. Load no more than the maximum number of sheets and do not
exceed the indicator line.
► Placing the original and adding paper (page 5)
Are multiple sheets feeding at once?
■ Fan the paper well before loading it.
Are you using paper that is not within
the specifications?
the specifications?
■ Use SHARP-recommended paper.
Using paper that is for other models or special paper that is not supported may
result in misfeeds, creases, or smudges.
⇒ - "SUPPLIES" in Start Guide
For paper that is prohibited or not recommended, see User's Manual.
result in misfeeds, creases, or smudges.
⇒ - "SUPPLIES" in Start Guide
For paper that is prohibited or not recommended, see User's Manual.
Are the bypass tray guides adjusted
to the width of the paper?
to the width of the paper?
■ Adjust the bypass tray guides to the width of the paper so that they slightly
contact the sides of the paper.
► Placing the original and adding paper (page 5)
Is the bypass tray extension guide
pulled out?
pulled out?
■ When loading large-size paper, pull out the extension guide.
► Placing the original and adding paper (page 5)
Is the bypass feed roller dirty?
■ Clean the surface of the bypass feed roller.
► Maintenance (page 6)
Is A5 (5-1/2" x 8-1/2") size paper
loaded?
loaded?
■ When loading A5 (5-1/2" x 8-1/2") size paper, place the paper in the horizontal
(A5R (5-1/2" x 8-1/2"R)) orientation. (Excluding cassette 1 and the bypass tray)
Is the paper size specified?
■ If you are using a non-standard size, be sure to specify the paper size.
If the size of paper loaded into a tray was changed, be sure to check the paper
size setting.
⇒ "Setting mode" → [System Settings] → [Common Settings] → [Paper Settings]
size setting.
⇒ "Setting mode" → [System Settings] → [Common Settings] → [Paper Settings]
→ [Paper Tray Settings] → [Tray Registration]
Did you add paper to the bypass tray?
■ When adding paper, remove any paper remaining in the bypass tray, combine it
with the paper to be added, and reload as a single stack.
If paper is added without removing the remaining paper, a misfeed may result.
Are you using punched paper?
■ When using punched paper, set the paper type to punched.
⇒ "Setting mode" → [System Settings] → [Common Settings] → [Paper Settings]
→ [Paper Tray Settings] → [Tray Registration]
Check
Solution
!
?
!
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man35) service manuals if exist.