Read Sharp AR-F14 (serv.man8) Service Manual online
AR-F14/PN1 ADJUSTMENTS 8-2
C. Registering the Number of Punch Hole
Perform the following to register the type of puncher unit (number of
holes) used to the IC on the punch controller PCB for identification by the
finisher. Be sure to register the type whenever you have replaced the
punch controller PCB.
punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB
as follows:
Fig.F05-102-02
2) Press SW1002 on the punch controller PCB to select the appropriate
number of punch holes.
•Each press on SW1002 moves the selection through the following
(repeatedly from top to bottom).
3) Press SW1003 on the punch controller PCB twice. The presses will
store the selected number of punch holes on the punch controller
PCB.
PCB.
•A single press on SW1003 will cause the LED indication to flash;
another press on SW1003 will cause the indication to remain ON to
indicate the end of registration.
indicate the end of registration.
4) Shift all bits of DIPSW1001 to OFF.
D. After Replacing the EEP-ROM (IC1002)
1) Turn off the host machine.
2) Set bits 1 through 4 on the punch controller PCB as follows:
Fig.F05-102-03
3) Press SW1002 and SW1003 on the punch controller PCB at the
same time.
•The presses will initialize the EEP-ROM. At the end, all LEDs
(LED1001, LED1002, LED1003) will go ON.
4) Adjust the sensor output, and store the number of punch holes.
E. Setup by the diag simulation of the copier
1) Select "SADDLE FINISHER SETTING" in SIM 3-10.
2) Select a setup item and change the setup value.
Number of punch holes
LED1001
LED1002
LED1003
2 holes (Puncher Unit-J1)
ON
OFF
OFF
2/3 holes (Puncher Unit-K1)
ON
ON
OFF
4 holes (Puncher Unit-G1)
OFF
OFF
OFF
4 holes (Puncher Unit-H1)
OFF
OFF
ON
ON
1
2
3
4
ON
1
2
3
4
Adjustment content
Default
value
Setup
range
range
Change/Setup
value 1
1 Saddle binding position
adjustment
0 - 400
0.0707mm
2 Saddle folding position
adjustment
0 - 400
0.0525mm
3 Front alignment position
adjustment
0 - 20
0.367mm
4 Rear alignment position
adjustment
0 - 20
0.367mm
5 Staple front one-position
binding position adjustment
0 - 200
0.04374mm
6 Staple rear one-position
binding position adjustment
0 - 200
0.04374mm
7 Staple 2-position binding
center adjustment
0 - 200
0.04374mm
8 Staple 2-position binding pitch
adjustment
0 - 100
0.04374mm
9 Punch center position
adjustment (FR direction)
47 - 53
10 Punch hole position
adjustment
(paper feed direction)
(paper feed direction)
0 - 100
0.105mm
SIMULATION 3-10
SADDLE FINISHER SETTING. SELECT 1-10, AND PRESS
START.
START.
1: SADDLE POSITION
2: FOLDING POSITION
3: FRONT ADJUST
4: REAR ADJUST
5: STAPLE REAR
6: STAPLE FTONT
7: STAPLE BOTH
8: STAPLE PITCH
9: PUNCH CENTER
10: PUNCH HOLE
200
1
200
10
10
100
100
100
50
50
50
SIMULATION 3-10
SADDLE FINISHER SETTING. EXECUTING…
200
200
SIMULATION 3-10
SADDLE FINISHER SETTING. ERROR
SIMULATION 3-10
SADDLE FINISHER SETTING. INPUT VALUE 0-400, AND
PRESS START.
PRESS START.
1:SADDLE POSITION
1:SADDLE POSITION
1:SADDLE POSITION
200
Press [CUSTOM SETTING] key
Terminated
Enter 1 and
Press [START] key
Press [START] key
Enter an adjustment value and
press [START] key .
press [START] key .
(Input display)
(Execution display)
[08]ADJUSTMENTS.fm 2 ページ ２００４年４月２７日 火曜日 午後７時５分
Display
