Read Sony SAL70200G2 Service Manual online
2-12
SAL70200G2 (2.8/70-200 G SSM Ⅱ) (70-200mm F2.8 G SSM II)
HELP17
Anti-diffusion agent (A-20): J-6082-611-A
Adhesive bond (B-10): J-6082-612-A
Adhesive bond (B-40): J-6082-614-A
Adhesive bond (B-10): J-6082-612-A
Adhesive bond (B-40): J-6082-614-A
1. Apply the adhesive bond (B-40) to the tip of screw portion of zoom stopper pin.
2. Install two pieces of anti slip rubber.
3. Apply the anti-diffusion agent (A-20) to all circumferences of indicated portion of zoom connect plate.
4. Insert two pieces of zoom connect plate in the groove of 4th lens barrel and tighten firmly four screws.
2. Install two pieces of anti slip rubber.
3. Apply the anti-diffusion agent (A-20) to all circumferences of indicated portion of zoom connect plate.
4. Insert two pieces of zoom connect plate in the groove of 4th lens barrel and tighten firmly four screws.
Loosen the screws half turn.
5. After moving the zoom operation ring little by little, tighten firmly the screws.
Note:
Do not operate the zoom until the zoom stopper pin is installed.
6. Apply the adhesive bond (B-10) to the indicated portion of zoom connect plate.
After tightening four screws,
loose the screws half turn
loose the screws half turn
Zoom Connect Plate
Zoom Connect
Plate
Plate
Anti-Slip
Rubber
Rubber
Anti-Slip
Rubber
Rubber
Insert in the groove
of 4th lens barrel
of 4th lens barrel
Groove
of 4th lens barrel
of 4th lens barrel
Zoom Stopper Pin
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
Apply the
anti-diffusion
agent (A-20)
(All around)
anti-diffusion
agent (A-20)
(All around)
Apply the adhesive bond (B-10)
Zoom Connect Plate
Note:
Do not operate the zoom until
the zoom stopper pin is installed.
Do not operate the zoom until
the zoom stopper pin is installed.
HELP18
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-15): J-6082-619-A
Grease (G-85): J-6082-626-A
Grease (G-15): J-6082-619-A
Grease (G-85): J-6082-626-A
1. Apply the ant-diffusion agent (A-20) to the indicated portion of zoom operation ring.
2. Apply the grease (G-15) (G-85) to the indicated portion of zoom operation ring.
2. Apply the grease (G-15) (G-85) to the indicated portion of zoom operation ring.
Apply the
anti-diffusion
agent (A-20)
(All around)
anti-diffusion
agent (A-20)
(All around)
Apply the
anti-diffusion
agent (A-20)
(All around)
anti-diffusion
agent (A-20)
(All around)
Apply the
grease (G-85)
(All around)
grease (G-85)
(All around)
Area
(all around)
restricted to
apply the
anti-diffusion
agent (A-20)
(all around)
restricted to
apply the
anti-diffusion
agent (A-20)
Apply the
grease (G-15)
grease (G-15)
Inside
Outside
Inside
Outside
3mm
Cut
view
view
Zoom Operation
Ring
Ring
Surroundings of
brush hole
brush hole
Apply the anti-diffusion
agent (A-20)
agent (A-20)
Cut
view
view
3. Install the zoom operation ring to the mirror tube, aligning the brush hole of zoom operation ring with the red index of mirror tube and
aligning three projections of zoom operation ring with the grooves as shown in the figure below.
Projections
Projection
Projection
Projection
Brush
Hole
Hole
Zoom Operation
Ring
Ring
Insert 3 projections of zoom operation ring in the
grooves of front holding tube block at 3 locations
and rotate the zoom operation ring in the arrow
direction.
grooves of front holding tube block at 3 locations
and rotate the zoom operation ring in the arrow
direction.
Zoom Operation
Ring
Ring
Groove
Groove
Groove
Groove
Groove
Front Holding
Tube Block
Tube Block
Red index of
mirror tube
mirror tube
Click on the first or last page to see other SAL70200G2 service manuals if exist.