MX-FNX10 (serv.man38). IMPROVEMENT OF SADDLE FINISHER (MX-FN10) - Sharp Copying Equipment Technical Bulletin (repair manual). Page 16

Read Sharp MX-FNX10 (serv.man38) Technical Bulletin online

Note 2 
When you return the Cover-TR-Wall, pay attention to the route of the harness. Fix the harness tightly with the 
clamp so that it does not interfere with the belt. 
 
 
 
Note 3 
When you attach the rear cover, pay attention to the wiring of the interface cable, and make sure it is not 
twisted or become loose. If it is twisted or loose, the cover may not be attached correctly. 
 
 
 
Note 4 
Attach the right screw types according to the instruction. (It is described in the procedure for removing them.) 
 
This is the end of confirmation and correction of phase deviation. 
 
 
 
 
 
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-621 
Page of 16
Display

Download Sharp MX-FNX10 (serv.man38) Technical Bulletin

Found More:

MX-FNX10 (serv.man38) Service Manuals

Preview DownloadPagesSize
MX-FNX10 MX-FN10 Service Manual (Complete) Service Manual 56 17.37 MB
MX-FNX10 (serv.man2) Parts Guide (Revised July 2017). Parts Guide 72 11.09 MB
MX-FNX10 (serv.man22) MACHINE NOISE REDUCED DURING INITIAL OPERATION Technical Bulletin 2 141.44 KB
MX-FNX10 (serv.man40) F1-43 TROUBLE CAUSED BY LOCKED ADJUSTMENT PLATE Technical Bulletin 2 197.65 KB
MX-FNX10 (serv.man23) F1-43 TROUBLE CODE OCCURRENCE RESULTING FROM SADDLE ALIGNMENT GLITCH WHEN POWER IS ON Technical Bulletin 3 356.31 KB
MX-FNX10 (serv.man24) SUPPORT FOR JAMMING (FPPD2_S, ETC.) IN THE SADDLE OPENING Technical Bulletin 3 619.27 KB
MX-FNX10 (serv.man25) IMPROVED PAPER FEEDING PERFORMANCE THROUGH THE SADDLE FOR A3 SIZE, ETC. Technical Bulletin 2 88.14 KB
MX-FNX10 (serv.man26) LASTING SUPPORT FOR THE STAPLER UNIT OPERATION LOCK (F1-08 ERROR CODE) Technical Bulletin 2 104.06 KB
MX-FNX10 (serv.man27) DELIVERY SENSOR LEVER OF THE MAIN UNIT COMING LOOSE WHEN THE RELAY UNIT (MX-RBX3) IS PULLED Technical Bulletin 2 114.32 KB
MX-FNX10 (serv.man28) F1-08 ERROR CAUSED BY AN OPERATION LOCK OF THE STAPLER UNIT Technical Bulletin 3 293.47 KB
MX-FNX10 (serv.man29) GUIDE SR-SG-GP-F R NOT OPENING CAUSING ANGLED PAPER EJECTION Technical Bulletin 2 87.18 KB
MX-FNX10 (serv.man30) FPDD_S JAMMING CAUSED BY THE SPRING OF THE UDG ARM SHAFT BREAKING Technical Bulletin 2 84.58 KB
MX-FNX10 (serv.man31) IMPROVED PAPER FEEDING PERFORMANCE THROUGH THE SADDLE FOR A3 SIZE (FPPD3_N) Technical Bulletin 2 114.12 KB
MX-FNX10 (serv.man32) INCREASE TO THE PAPER SKEW DURING SWITCHBACK TRANSPORT Technical Bulletin 2 72.23 KB
MX-FNX10 (serv.man33) FN10 ROM UPGRADE ... (5).FIX FOR FPDD_S JAMS Technical Bulletin 1 26.16 KB
MX-FNX10 (serv.man34) PART DISCONTINUATION AND PROFILE CHANGE DUE TO PRODUCTION EFFICIENCY INCREASE Technical Bulletin 2 106.98 KB
MX-FNX10 (serv.man35) SADDLE STAPLE JAM (FPPD3_N) NORMALLY A3 Technical Bulletin 3 240.66 KB
MX-FNX10 (serv.man36) IMPROVEMENTS TO SADDLE STITCH FINISHER (MX-FN10) Technical Bulletin 4 290.66 KB
MX-FNX10 (serv.man37) ROM UPGRADE ... (2) TO (3) Technical Bulletin 2 39.67 KB
MX-FNX10 (serv.man39) ROM UPGRADE 1 Technical Bulletin 1 18.63 KB
MX-FNX10 (serv.man20) ENHANCEMENT FOR JAM CAUSED BY WORN OUT TRANSPORT RIBS ON TOP COVER Technical Bulletin 2 66.14 KB
MX-FNX10 (serv.man19) IMPROVEMENT OF STRENGTH OF SADDLE STITCH GEAR Technical Bulletin 2 206.51 KB
MX-FNX10 (serv.man18) MX-FNX9 FN10 FN11 FN18 PNX6 ROM CHANGE FOR VIRGO 2 MODELS - MX-4140 4141 5140 5141N - BULLETIN ONLY Technical Bulletin 1 19.73 KB
MX-FNX10 (serv.man17) ARE-1123 MXFN10 Firmware Upgrade B88 V01.14.02.00 Model specific separate folders inside (Bulletin Only) Technical Bulletin 1 81.26 KB
MX-FNX10 (serv.man16) ELIMINATION REDUCTION OF SPRINGS FOR PRODUCTIVITY IMPROVEMENT. Technical Bulletin 2 178.66 KB
MX-FNX10 (serv.man15) SETUP OF NEW SERVICE PARTS FOR SADDLE STAPLER AS SINGLE ITEM. Technical Bulletin 2 132.15 KB
MX-FNX10 (serv.man14) CCE-1402 ADDITION OF PROTECTOR SHEET FOR FALL PREVENTION OF A SENSOR PREVENTION OF F1-31 Technical Bulletin 2 197.35 KB
MX-FNX10 (serv.man13) Firmware update (14). Technical Bulletin 1 55.04 KB
MX-FNX10 (serv.man21) CCE-1099 - ENHANCEMENT FOR PAPER MISALIGNMENT OF FOLDING DUE TO SKEW AT SADDLE Technical Bulletin 1 125 KB
MX-FNX10 (serv.man3) Firmware update (14). File contains model specific folders and Technical Bulletin. Driver / Update 2.75 MB
MX-FNX10 (serv.man4) ARE-1123 MXFN10 Firmware Upgrade B88 V01.14.02.00 Model specific separate folders inside (Bulletin Embedded) Driver / Update 2.3 MB
MX-FNX10 (serv.man5) For MX4140N-5141N Models -Production Run September 2013 Driver / Update 267.89 KB
MX-FNX10 (serv.man6) Special firmware for F1-08 problems Driver / Update 1.53 MB
MX-FNX10 (serv.man7) For MXM283 363N and MX453 503N Production Run Date July 2010 - FIX FOR FPDD_S JAMS Driver / Update 223.59 KB
MX-FNX10 (serv.man8) For MX4100 1N and MX5000 1N Production Run Date July 2010 - FIX FOR FPDD_S JAMS Driver / Update 224.46 KB
MX-FNX10 (serv.man9) For MX2600N and MX3100N Production Run Date July 2010 - FIX FOR FPDD_S JAMS Driver / Update 224.47 KB
MX-FNX10 (serv.man10) For MXM283 363N and MX453 503N Production Run Date May 2009 Driver / Update 285.45 KB
MX-FNX10 (serv.man11) For MX4100N and MX5000N Production Run Date May 2009 Driver / Update 286.33 KB
MX-FNX10 (serv.man12) For MX2600N and MX3100N Production Run Date May 2009 Driver / Update 286.33 KB

Random: