Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual online
MX-7000N SIMULATION 7 – 6
44
1
Used to set each correction operation function in the image forming
(process) section.
(process) section.
Setting
Process (Photoconductor/
Developing/Transfer/
Cleaning)
Developing/Transfer/
Cleaning)
2
Image density sensor gain adjustment
Adjustment/Setting
Process
4
Used to set the target density level in the image density correction.
(Do not use this function unless
specially required.)
specially required.)
6
Used to execute the high density process correction compulsorily.
Adjustment
9
Used to check data of correction results in the image forming section.
(Do not use in the market.)
Process (Photoconductor/
Developing/Transfer/
Cleaning)
Developing/Transfer/
Cleaning)
12
Used to check the sampling toner image patch density data in the image
density correction.
density correction.
(Do not use in the market.)
Image process
(Photoconductor/
Developing)
(Photoconductor/
Developing)
13
Used to adjust the color image sensor.
Adjustment/Setting
14
Used to check the output level of the temperature/humidity sensor.
Adjustment, setting, operation data
check
check
Image process
(Photoconductor/
Developing)
(Photoconductor/
Developing)
16
Used to check the toner density control data.
(Do not use in the market.)
21
Used to set the half tone process control.
Adjustment/Setting
Process
22
Used to check the toner patch image density level of each color in half tone
image forming section correction (process correction).
image forming section correction (process correction).
(Do not use in the market.)
24
Used to display the process control result.
(Do not use in the market.)
25
Used to set the initial conditions of the process control half tone correction.
(Do not use in the market.)
26
Used to execute the half tone process control compulsorily.
Adjustment/Setting
Process
27
Used to clear the half tone process correction value.
Data clear
28
Used to set the process control execution timing.
Adjustment/Setting
29
Used to select the half tone correction during a job.
(Do not use in the market.)
31
Used to adjust the phase of the photoconductor.
Adjustment/Setting
Process
37
Used to perform the image density correction setting.
Adjustment/Setting
43
Used to check installation of the developing unit and the current state.
(Do not use in the market.)
52
Used to check the image density level of each color toner patch in 1-pixel
half tone correction.
half tone correction.
(This simulation should not be
executed unless specially required.)
executed unless specially required.)
54
The 1-pixel half tone correction result is displayed.
(This simulation should not be
executed unless specially required.)
executed unless specially required.)
56
The 1-pixel half tone correction is executed compulsorily.
(This simulation should not be
executed unless specially required.)
executed unless specially required.)
57
The 1-pixel half tone correction value is cleared.
(This simulation should not be
executed unless specially required.)
executed unless specially required.)
46
1
Used to adjust the copy density in the copy mode.
Adjustment (Color copy mode)
2
Used to adjust the copy density in the copy mode.
Adjustment (Monochrome copy
mode)
mode)
4
Used to adjust the density in the scanner mode.
Adjustment (Color scanner mode)
5
Used to adjust the density in the scanner mode.
Adjustment (Monochrome scanner
mode)
mode)
8
Used to adjust the scanner color balance RGB.
Adjustment (Color scanner mode)
9
Used to adjust the copy density in the copy mode.
Adjustment (DSPF mode)
10
Used to adjust the engine color balance manually.
Adjustment
16
Used to perform the engine color balance manual adjustment (monochrome,
all modes).
all modes).
Adjustment
19
Used to set the monochrome auto exposure mode.
Setting
21
Used to perform the engine color balance manual adjustment (color, all
modes).
modes).
Adjustment
23
Used to perform the half tone highest density correction.
Adjustment/Setting
24
Used to perform the engine half tone auto density adjustment.
Adjustment
25
Used to perform the color balance adjustment in the single color mode.
Adjustment
26
Used to perform the default setting of color balance in the single color mode.
Adjustment
27
Used to perform the engine/gamma calculation formula coefficient setting.
Adjustment/Setting
28
Used to check Auto exposure/Document auto recognition/Line number
recognition (color mode).
recognition (color mode).
(This simulation should not be used
unless specially required.)
unless specially required.)
33
Used to perform the color auto mode adjustment.
Adjustment/Setting
36
2-color (red/black) copy adjustment
Adjustment/Setting
37
Used to perform the black/white image generation adjustment.
Adjustment/Setting
39
Used to perform the image send sharpness adjustment.
Adjustment/Setting
40
Used to perform the collective adjustment of all the FAX exposure modes.
Adjustment/Setting
41
Used to perform the FAX exposure adjustment (normal character).
Adjustment/Setting
42
Used to perform the FAX exposure adjustment (small character).
Adjustment/Setting
43
Used to perform the FAX exposure adjustment (fine).
Adjustment/Setting
44
Used to perform the FAX exposure adjustment. (Super fine)
Adjustment/Setting
45
Used to perform the FAX exposure adjustment (600dpi).
Adjustment/Setting
47
Used to perform the JPEG compression rate setting in copying and
scanning.
scanning.
Adjustment/Setting
Main
Sub
Function (Purpose)
Purpose
Section
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.