Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual online
MX-7000N SIMULATION 7 – 3
2. List of simulation codes
Main
Sub
Function (Purpose)
Purpose
Section
1
1
Used to check the operations of the scanner (read) unit and its control
circuit.
circuit.
Operation test/Check
Optical (Image scanning)
2
Used to check the operation of sensor in the scanning (read) section and the
related circuit.
related circuit.
Operation test/Check
Optical (Image scanning)
5
Used to check the operations of the scanner (read) unit and its control
circuit.
circuit.
Operation test/Check
Optical (Image scanning)
2
1
Used to check the operations of the automatic document feeder unit and the
control circuit.
control circuit.
Operation test/Check
DSPF
2
Used to check the operations of the sensors and detectors in the automatic
document feeder unit and the control circuits.
document feeder unit and the control circuits.
Operation test/Check
DSPF
3
Used to check the operations of the loads in the automatic document feeder
unit and the control circuits.
unit and the control circuits.
Operation test/Check
DSPF
3
2
Used to check the operation of sensor and detector in the finisher and the
control circuits.
control circuits.
Operation test/Check
Finisher
3
Used to check the operation of the load in the finisher and the control circuit.
Operation test/Check
Finisher
10
Used to adjust the finisher.
Adjustment
Finisher
30
Used to check the operations of the sensors and detectors in the inserter
and the control circuits.
and the control circuits.
Operation test/Check
Inserter
31
Used to check the operations of the loads in the inserter and the control
circuit.
circuit.
Operation test/Check
Inserter
32
Used to set the adjustment value of the inserter paper width detection level.
Setting (Adjustment)
Inserter
4
2
Used to check the operations of the sensors and detectors in the large
capacity tray (LCC) and the control circuit.
capacity tray (LCC) and the control circuit.
Operation test/Check
Large capacity tray (LCC)
3
Used to check the operations of the loads in the large capacity tray (LCC)
and the control circuit.
and the control circuit.
Operation test/Check
Large capacity tray (LCC)
5
Used to check the operations of the clutch (LTRC) in the LCC and the
monitor.
monitor.
Operation test/Check
Large capacity tray (LCC)
5
1
Used to check the operation of the display, LCD in the operation panel, and
control circuit.
control circuit.
Operation test/Check
Operation panel
2
Used to check the operation of the heater lamp and the control circuit.
Operation test/Check
Fusing
3
Used to check the operation of the copy lamp and the control circuit.
Operation test/Check
Optical (Image scanning)
4
Used to check the operation of the discharge lamp and the control circuit.
Operation test/Check
Process
6
1
Used to check the operations of the loads (clutches and solenoids) in the
paper transport system and the control circuits.
paper transport system and the control circuits.
Operation test/Check
Paper transport/paper exit
2
Used to check the operations of each fan motor and its control circuit.
Operation test/Check
Other
3
Used to check the operations of the primary transfer unit and the control
circuit.
circuit.
Operation test/Check
Process (Transfer)
4
Used to check the operations of the PTC and the MC cleaner.
Operation test/Check
7
1
Used to set the operating conditions of aging.
Setting
Other
6
Used to set the intermittent aging cycle.
Setting
8
Used to display the warm-up time.
Operation display
9
Used to set a color in the color mode printing. (Used to check the print in the
color mode.)
color mode.)
Operation test/Check
8
1
Used to check and adjust the operations of the developing voltage in each
print mode and the control circuit.
* When the middle speed is adjusted, the high speed and the low speed are
also adjusted simultaneously.
print mode and the control circuit.
* When the middle speed is adjusted, the high speed and the low speed are
also adjusted simultaneously.
Operation test/Check/Adjustment
Process (Developing)
2
Used to check and adjust the operations of the main charger grid voltage in
each printer mode and the control circuit.
* When the middle speed is adjusted, the high speed and the low speed are
also adjusted simultaneously.
each printer mode and the control circuit.
* When the middle speed is adjusted, the high speed and the low speed are
also adjusted simultaneously.
Operation test/Check/Adjustment
Process (Charging)
6
Used to check and adjust the operation of the transfer voltage and the
control circuit.
control circuit.
Operation test/Check/Adjustment
Process (Transfer)
9
2
Used to check the operations of the sensors and detectors in the duplex
section and its control circuit.
section and its control circuit.
Operation test/Check
Duplex
3
Used to check the operations of the loads in the duplex section and the
control circuits.
control circuits.
Operation test/Check
Duplex
10
1
Used to check the operation of the load (motor) in the process section and
the related circuits.
* This check must be performed with no toner bottle installed.
the related circuits.
* This check must be performed with no toner bottle installed.
Operation test/Check
Process (Developing)
2
Used to check the operations of the toner remaining quantity sensor and the
control circuit.
control circuit.
Operation test/Check
Process (Developing)
13
-
Used to cancel the self-diag "U1" trouble.
Clear/cancel (Trouble etc.)
14
-
Used to cancel excluding the self-diag "U1/U2/LCC/PF" troubles.
Clear/cancel (Trouble etc.)
15
-
Used to cancel the self-diag "U6-09, F3-12, F3-22 (large capacity paper feed
tray, paper feed tray 1, 2)" trouble.
tray, paper feed tray 1, 2)" trouble.
Clear/cancel (Trouble etc.)
LCC
16
-
Used to cancel the self-diag "U2" trouble.
Clear/cancel (Trouble etc.)
MFPcnt PWB /
PCU PWB / SCU PWB
PCU PWB / SCU PWB
17
-
Used to cancel the self-diag "PF" trouble.
Clear/cancel (Trouble etc.)
21
1
Used to set the maintenance cycle.
Setting
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.