Read Sharp AM-400 (serv.man8) Service Manual online
AM-400DE
2 – 10
2.1.9 Dial test mode
The mode is used to inspect whether dialing is accurate in two kinds of
dial modes or not. All data which can be dialed in this mode are auto-
matically called up in both PB and DP mode.
dial modes or not. All data which can be dialed in this mode are auto-
matically called up in both PB and DP mode.
When this mode is activated, the following operations will be automati-
cally executed to their ends. Whenever the dialed content is right or
not is judged with the external instrument which is connected to the
line cable.
cally executed to their ends. Whenever the dialed content is right or
not is judged with the external instrument which is connected to the
line cable.
1. After pressing [ENTER] key, the CML relay is turned on, and the
following numbers are dialed in the PB mode.
“1”, “2”, “3”, “4”, “5”, “6”, “7”, “8”, “9”, “
“, “0”, “#”
2. And the following numbers are dialed in the DP mode.
“1”, “5”, “9”, “0”
3. After dialing, the CML relay is turned off.
2.1.10 Auto feeder mode
Inserting and discharging the document can check the auto feeder.
The information of document sensor (A4 sensor) and ORG sensor is
displayed when the documents are inserted to the Auto Feeder.
displayed when the documents are inserted to the Auto Feeder.
1. Operation
2. Press [STOP] key to exit the mode.
2.1.11 Flash memory test
The Flash memory is checked.
Note: If this is excessively repeated, it will shorten the life of the Flash
memory.
memory.
2.1.12 Gear change mode
The gear to drive ADF and flatbed mechanism will be aging continu-
ously and the number of switching will appear on the LCD.
ously and the number of switching will appear on the LCD.
1. Operation
2. Note
ADF and FLATBED counter will be 0 over 65535.
Press [STOP] key to exit the mode.
2.1.13 Flatbed aging
Scanner motor will be driven based on the motor speed for each reso-
lution. By pressing the [>] key or the [<] key, you can select the motor
speed preliminary.
lution. By pressing the [>] key or the [<] key, you can select the motor
speed preliminary.
1. Operation
2. Press [STOP] key to exit the mode.
2.1.14 Message print (AM-400DE/F/IT/SE only)
In this mode, all the message data, which are used for displaying indi-
cation and list print are printed as a contrast table of the selected lan-
guage and English.
cation and list print are printed as a contrast table of the selected lan-
guage and English.
No.
Flash memory
Alarm Buzzer
Remarks
1
NOR-Flash
1 time <Long sound>
DIAL TEST
123456789 #
1590
[ENTER]Key
Go to Auto Feeder Mode
AUTO FEEDER
300 MONO
600 MONO
300 COLOR
600 COLOR
[ENTER]Key
[>] Key
[>] Key
[>] Key
Feeding documents will start
by pressing ENTER key.
by pressing ENTER key.
(
)
A4 (A4
)
without documents
with documents
A4 (A4
ORG)
End
FLASHM EMORY
[ENTER]Key
NOW CHECKING
FLASH OK
When an error occurs, the alarm will sound.
GEAR CHARGE MODE
ADF : COUNT = 00001
FBED : COUNT = 00001
ADF : COUNT = 00002
FBED : COUNT = 00002
[ENTER]Key
Drive the gear as Flatbed mode.
Move from Home Position to the reading direction. After
pause, move to the reading position from ADF.
pause, move to the reading position from ADF.
Drive the gear as ADF mode.
Pause and drive reversely.
Move from Home Position to the reading direction.
After pause, move to the reading position from ADF.
Pause and drive reversely.
This sequence will be terminated by pressing STOP key.
Drive the gear as ADF mode.
Drive the gear as Flatbed
Press STOP key to terminate this aging.
MOTOR AGING MODE
300 MONO
600 MONO
300 COLOR
600 COLOR
[ENTER]Key
[>] Key
[>] Key
[>] Key
Aging will start
by pressing ENTER key.
by pressing ENTER key.
Click on the first or last page to see other AM-400 (serv.man8) service manuals if exist.