AM-400 (serv.man8). Chapter 2 (Adjustments). - Sharp Copying Equipment Service Manual (repair manual). Page 12

AM-400DE

2 – 12

This mode is used for print aging.

Select the desired pattern and input cycle, counter, pages for aging.

Printing size depends on Paper Size setting in Common Setting.

1. Printing pattern

2. Printing interval [CYCLE]: The time from printing end to next print-

ing start.

Input Range: 001 to 999 seconds or 001 to 999 minutes.

3. Repeat printing [COUNT]: The number of printing cycle.

Input Range: 0001 to 9999 times.

4. Printing pages [PAGE]: The printing pages in one cycle of printing.

Input Range: 001 to 999 pages.

This mode is used for COPY Aging. The document on the flatbed or
ADF will be scanned at the beginning of each cycle and printed it. The
meaning of “CYCLE”, “COUNT” and “PAGE” are same as the case
“CONTINUOUS PRINT”.

Printing size depends on Paper Size setting in Common Setting.

This mode is used to set the life counter of the printer and the counter
of the scanner at desired values and to clear them.

The values of life counter can be set in this mode.

1. Enter life set mode.

2. The cursor blinks at the top data. Four counters can be selected.

Select the desired counter and input the counter value of 10 digits
using the numeric keys. Pressing the [ENTER] key changed the
counter value.

Note: Toner page counter cannot be changed.

Caution: These counters are not cleared after memory clear mode
is executed. If it is necessary to execute the memory clear mode on
repairing the PWB, these life counters should be set again at the
same time.

1: Check Pattern

: same as Figure 1

2: All White pat-
tern

: Not printed

3: All Black pat-
tern

: Printed with black within print area

4: Area pattern

: Frame line is printed within print area

5: Stripe pattern

: Lateral stripe (Black 2 lines and White 2 lines)

6: Halftone pat-
tern

: same as Figure 3

7: Phil chart

: PHIL CHART pattern

8: General pattern
9: 5 % chart
10: SG chart
11: IDBG chart

Start aging

CYCLE=000(s)

CYCLE=000(m)

Enter the cycle and press the [ENTER] key.

COUNT=0000(time)

Enter the counter and press the [ENTER] key.

PAGE=000(sheet)

Enter a number of pages and press the [ENTER] key.

CONTINUOUS PRINT

[ENTER]Key

1: CHECK PATTERN

2: ALL WHITE

3: ALL BLACK

4: AREA PATTERN

7: PHIL CHART

8: GENERAL CHART

[>]Key

[>]Key

[>]Key

[>]Key

[>]Key

[>]Key

9: 5% CHART

[>]Key

5: STRIP PATTERN

[>]Key

6: H-TONE PATTERN

10: SG CHRAT

11: IDBG CHART

[>]Key

[>]Key

[>]Key

Select the desired pattern with the [

>

]key and [

<

]key and press the [ENTER] key.

[>]Key

COPY AGING

[ENTER]Key

Start aging

CYCLE=000(s)

CYCLE=000(m)

Enter the cycle and press the [ENTER] key.

COUNT=0000(time)

Enter the counter and press the [ENTER] key.

PAGE=000(sheet)

Enter a number of pages and press the [ENTER] key.

[>]Key

LIFE MODE

[ENTER]Key

1: LIFE SETMODE

2: LIFE CLEAR

[>]Key

[ENTER]Key

0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0

[ENTER]Key

1: SCAN(ADF)

3: PRINT

4: DRUM

5: TONER PAGE

6: TONER DOTCOUNT

LIFE MODE

[ENTER]Key

[ENTER]Key

[ENTER]Key

[ENTER]Key

cursor position

[>]Key

[>]Key

[>]Key

[>]Key

[>]Key

0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0

2: SCAN(FB)

[ENTER]Key

[>]Key