Read Sharp UP-X500 (serv.man5) Service Manual online
CODE : 00Z
q
INSTALLATION MANUAL
CONTENTS
Parts marked with "
!
" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
UPX500VIME
POS TERMINAL
MODEL
UP-X500
(V version)
1.
Removing the rear cover unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.
Removing the side cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3.
Removing the LCD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4.
Removing the MCR unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5.
Fixing the HDD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6.
Removing the AC cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7.
Removing the AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
8.
Removing the Main board (Extention RAM module) . . . . . . . . . . . . . . . . 3
9.
COM port connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9-1. FIXING THE REAR DISPLAY UP-I20DP. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9-2. FIXING THE POLE DISPLAY: UP-P20DP/DPB . . . . . . . . . . . . . . . . . . . . . 4
9-3. FIXING THE DRAWER UNIT: ER-03DW/04DW . . . . . . . . . . . . . . . . . . . . . 4
9-4. FIXING THE LAN CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
10. Removing the contactless clerk key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
11. Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
UP-X500VI
BATTERY DISPOSAL
Contains Lithium Battery. Must be Disposed of Properly.
Contact Local Environmental Officials for Disposal Instructions.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
AVOID: SHORT-CIRCUITING THE BATTERY TERMINALS.
KEEP THE BATTERY AWAY FROM FIRE.
*
WHEN DISPOSING THE BATTERY, FOLLOW THE LOCAL
RULES AND REGULATIONS.
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS LITHIUM BATTERY.
THIS BATTERY MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR
STATE ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND
DISPOSAL OPTIONS.
“TRAITEMENT DES ACCUMULATEUR USAGÉS”
CE PRODUIT CONTIENT UN ACCUMULATEUR À LITHIUM.
CET ACCUMULATEUR USAGÉ DOIT ÊTRE TRAITÉ CORRECTEMENT.
ENLEVEZ L’ ACCUMULATEUR DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE
AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES
MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.
CONSUMPTION
• LCD (Back light) 15,000 h
• MCR unit 300,000 pass
UP-X500I
Removing the rear cover unit
– 1 –
1. Removing the rear cover unit
Remove the screw
1
, and remove the rear cover unit
2
.
2. Removing the side cover
Slide the lever
1
to release the lock. Slide the side cover
2
toward
you and rotate and remove it.
3. Removing the LCD unit
3-1. Removing the top cover section
Remove each screw
1
, and lift the rear side of the top cover
section
3
and disconnect each connector
2
and remove.
3-2. Removing the Top cover unit
Caution: Top cover unit
7
is pushed down.
1. Remove the screw
1
, and remove the wire holder
2
.
[Screw
1
is Black.]
2. Remove the screw
3
, and remove the wire holder
4
.
3. Remove the core
5
of the T/P cable.
4. Remove four screws
6
, and disassemble the top cover unit
7
.
Precautions
• Before installation, be sure to turn off the power.
• Use gloves to protect your hands from being cut by the angle and
the chassis.
• Connect all the cables securely. When connecting or disconnecting
the cables, be careful not to apply stress to the cables. (It may
cause disconnection.)
• Ground the human body to prevent against troubles and dust adhe-
sion to the LCD by static electricity. When assembling the LCD, use
a discharge blower to prevent against dust intrusion.
a discharge blower to prevent against dust intrusion.
• Be careful of the high voltage of the inverter PWB transformer.
• Place the top cabinet with LCD panel side down, Please use a clean
dust free clothe to protect the touch panel and LCD area.
1
1
2
2
1
1
1
1
1
2
2
3
1
2
3
4
5
6
6
7
UP-X500I
Removing the MCR unit
– 2 –
3-3. Removing the LCD cabinet
1.
Remove the screw
1
.
2.
Use a screwdriver to catch the notched section and disassemble
the MCR rear cabinet
the MCR rear cabinet
2
.
Caution: • Wrap the screwdriver with waste cloth when using it without
scratching the cabinet.
• Rotate it in the direction of A and slide it in the direction of B,
and it will come off easily.
3.
Remove two screws
3
, and disassemble the LCD rear cabinet
4
from the MCR side.
4.
Remove screw
5
, and disassemble the Clamp
6
.
3-4. Removing the LCD unit
1.
Remove six screws
1
, and remove the touch panel
2
, the inserter
cable
3
, and the LED cable
4
, and disassemble the LCD assembly.
2.
Remove four screws
5
, and disassemble the LCD unit
7
from the
LCD plate
6
.
Caution: Tighten the screw
1
at 3.5kg.
3-5. Removing the touch panel
Remove the T/P angle A
2
, T/P angle B
3
, with screws
1
.
And disassemble the Touch panel
2
.
4. Removing the MCR unit
1. Remove the MCR rear cabinet (Reference [3-3]).
2.
Remove the screw
1
, and remove the MCR cable
2
and disassemble
the MCR
3
.
1
B
A
2
3
3
4
5
6
Cloth
1
1
1
1
1
1
2
3
4
5
5
5
5
6
7
1
1
1
1
1
1
1
1
2
2
3
3
4
1
2
3
