UP-X500 (serv.man4). UP-X500 Service Manual - Sharp EPOS Service Manual (repair manual)

up-x500 (serv.man4) service manual
Model
UP-X500 (serv.man4)
Pages
75
Size
1.38 MB
Type
PDF
Document
Service Manual
Brand
Device
EPOS / UP-X500 Service Manual
File
up-x500-sm4.pdf
Date

Read Sharp UP-X500 (serv.man4) Service Manual online

CODE : 00Z
q
SERVICE MANUAL
CONTENTS
Parts marked with "
!
" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
UPX500VSME
POS TERMINAL
MODEL
UP-X500
(V version)
CHAPTER 1. SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
CHAPTER 2. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
CHAPTER 3. FIXING THE HDD UNIT . . . . . . . . . . . . . . . . . . . . . . 3 - 1
CHAPTER 4. DIAGNOSTICS SPECIFICATIONS  . . . . . . . . . . . . . 4 - 1
CHAPTER 5. CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . 5 - 1
CHAPTER 6. TOUCH PANEL CALIBRATION UTILITY . . . . . . . . . 6 - 1
CHAPTER 7. CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
UP-X500V   
BATTERY DISPOSAL
Contains Lithium Battery. Must be Disposed of Properly.
Contact Local Environmental Officials for Disposal Instructions.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
AVOID: SHORT-CIRCUITING THE BATTERY TERMINALS.
KEEP THE BATTERY AWAY FROM FIRE. 
*
 WHEN DISPOSING THE BATTERY, FOLLOW THE LOCAL 
RULES AND REGULATIONS. 
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS LITHIUM BATTERY.
THIS BATTERY MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR 
STATE ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND 
DISPOSAL OPTIONS.
“TRAITEMENT DES ACCUMULATEUR USAGÉS”
CE PRODUIT CONTIENT UN ACCUMULATEUR À LITHIUM.
CET ACCUMULATEUR USAGÉ DOIT ÊTRE TRAITÉ CORRECTEMENT.
ENLEVEZ L’ ACCUMULATEUR DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE 
AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES 
MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.
UP-X500V
Specifications
1 – 1
CHAPTER 1. Specifications
1. APPEARANCE
AC power cord
Plug your terminal into a wall outlet that has a dedicated ground before using.
Power switch
Set the power switch to the ON ( I ) position after the terminal has been
plugged in.
Power indicator
When the power switch is turned on, the power indicator will light up. The
indicator will remain on even while the display’s backlight is off.
Contactless clerk key
Put the key to the clerk switch.
 DISPLAY
Display angle
The display may be tilted for the best viewing angle.
The allowable angle of display is within 53 degrees as illustrated at the right.
Caution: Do not pull the display beyond the maximum tilt angle nor
apply excessive pressure to the display.
Make sure to hold the body when pulling the display so that
the terminal may not move.
  RESET SWITCH
DO NOT insert any object into this switch unless instructed to do.
Doing so may damage or delete the data.
2. RATING
 Front view
 Rear view
Magnetic card reader
Operator display
(touch panel)
Power indicator
AC power cord
Power switch
(located at the bottom cabinet)
Side cover
Side cover
Side cover release lever
(located at the bottom cabinet)
 Terminals inside the side cover
Parallel port
(for connection
with printer,etc.)
USB ports
(for connection with CD-ROM drive unit,
FDD unit, mouse, etc.)
PS/2 port
(for connection
with AT keyboard,
etc.)
Volume control 
(Turn frontwards to make sound volume
higher, and turn backwardsto make sound
volume lower.)
PC card slots
(Two Type 
II
 slots
or one Type 
III
slot are available.)
Reset switch
[Purpose] This switch is used to reset.
[Outline] The Reset switch is single shot type.
Push ON
: This position is used to restart the system when soft-
ware hang up.
U
V
Power supply
 AC 120V
AC 230 ~ 240V
Power
consumption
 43W
 43W
Ambient
temperature
and humidity
41 to 95°F(5 to 35°C)
20 to 90%
5 to 35°C (41 to 95°F)
20 to 90%
External
dimensions
12.5(W) x 12.2(D) x 11.2(H)
318(W) x 311(D) x 284 (H)
 318(W) x 311(D) x 284(H)
Weight
Approximately
12.6lb (5.7kg)
 5.7kg
53
UP-X500V
Specifications
1 – 2
3. HARDWARE
3-1. SYSTEM
3-2. EXTENTION RAM MODULE
POS Terminal has a socket as 184pin DIMM.
(Local Purchase)
512Mbytes 184pin DIMM
: DDR-SDRAM memory type PC2100 (more than): power 2.5V
3-3. DISPLAY
3-4. TOUCH PANEL
3-5. ETHERNET
3-6. COM PORTS
POS Terminal has 3 COM ports as RS232 interface.
In order to supply +5V power, CI signal and +5V power supply 
of COM2 can be switched.
The +5V power consumption of COM2 is Max 500mA.
3-7. HARD DISK DRIVE
3-8. PC-CARD & USB2.0 & PS/2 & VGA interface
PC-CARD slot & USB2.0 interface & PS/2 interface & VGA interface
can build in this machine.
3-9. OPTIONAL DEVICE INTERFACE
POS Terminal has 2 Drawer I/Fs, a Printer I/F, and a Customer display I/F.
Caution: UP-P20DP/DPB and UP-I20DP can not be used simultaneously
with installed on the same system because of their power capacity.
4. SOFTWARE
Item
Specifications
Note
CPU
VIA Eden Processor
733MHz
Chip set
VIA VT8623+VT8235
Graphics Chip
VIA VT8623
Main memory
128Mbytes 
DDR-SDRAM
MAX.512Mbytes
Video memory
16Mbytes
(Shared with Main memory)
Super I/O
SMSC SIO10N268
BIOS memory
512Kbytes
Flash ROM
Item
Specifications
Note
LCD type
TFT LCD
HT12x12-100
Screen size
12.1”
Resolution
XGA (1024 x 768 dots)
Module Size
261.5(W) x 199.5(H) x 5.5(D)
Dot Size
0.240 x 0.240 (mm)
Active Area
245.8 x 184.3 (mm)
Item
Specifications
Note
Type
Analog touch panel
N010-0554-T802
Module Size
261.4(W) x 198.8(H) x 2.8(D) (mm)
Viewing Area
247.7(W) x 186.5(H) (mm)
Active Area
246.5(W) x 185.3(H) (mm)
Number of
Positions
4096 x 4096 Positions
Item
Specifications
Note
Controller
VT6103
Speed
10Mb/s or 100Mb/s
connector
RJ45
COM1,COM2,COM3
: D-sub 9 pin
: Pin assign
1 pin CD
2 pin RD
3 pin SD
4 pin ER
5 pin GND
6 pin DR
7 pin RS
8 pin CS
9 pin CI/+5V
Item
Specifications
Note
Type
2.5 inch Hard Disk Drive 
Fujitsu MHT2030AT
Interface
ATA
Capacity
30Gbytes
• PC-CARD interface
: 2 ports (Type 
II
 x 2 or Type 
III
 x 1)
Two 16bit type PCMCIA cards can't be used
at same time.
• USB2.0 interface
: 2 ports
Power consumption
: +5V max. 0.5A
• PS/2 interface
: 1 port
• VGA interface
: 1 port
• Drawer I/F
: used for ER-03DW, ER-04DW and ER-05DW
•  Customer display I/F
: used for UP-P20DP/DPB or UP-I20DP
•  Printer I/F
: used for dongle
Item
Specification
Note
O/S
Provision
Any OS is not
pre-installed
Available OS
Windows 2000
Professional
L o c a l
purchesed
Windows XP
Professional
L o c a l
purchesed
Windows XP
Home
L o c a l
purchesed
OPOS
Available OS
Windows 2000
Professional
Windows XP
Professional
Windows XP
Home
Device Drivers
Drivers
POS drivers
provided by
SHARP
for Windows
2000
Touch keyboard,
MCR,
for Windows XP Drawer, etc.
Additional
device driver
Local purchased
BIOS
Contents
System, Control,
etc.
in 512 KB
Flash ROM
Application
software
Provision
For Hospitality
Local purchased
Page of 75
Display

Download Sharp UP-X500 (serv.man4) Service Manual (Repair Manual)

Here you can read online and download Sharp UP-X500 (serv.man4) Service Manual in PDF. UP-X500 (serv.man4) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp UP-X500 (serv.man4) EPOS. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.