WV-CS950, WV-CS954E - Panasonic Video Monitoring Service Manual (repair manual). Page 15

2-9

8

The Location of Test Points and Adjusting Controls refer
to Wiring Diagram on page 3-1.

8

Insert new floppy disk containing DOS Operating System
and the E.V.R. Adjustment Program into the computer
(IBM PC/AT) and turn on the Power Switch of the com-
puter.

8

When starting an adjustment, at the prompt, type
RADJ2 CS95E and press the ENTER key, an initial menu
page as shown in Fig. 4-1-1 will be displayed.

This saving procedure is recommended to keep the current
adjustment status of the camera.

8

Press the SAVE (F5) key of the computer, and the com-
puter will ask you for the file name.

8

Type  xxxxxxxx.EV2 B40 19FF. Give an appropriate file
name for xxxxxxxx within 8 letters, but do not use
CS95E.

8

Press the ENTER key.

This loading procedure is recommended to return the adjust-
ment status of the camera to the factory default setting or
the setting you saved before.

8

Press the LOAD (F1) key of the computer, and the com-
puter will ask you for the file name.

8

Type CS95E.EV2 or xxxxxxxx.EV2 (xxxxxxxx means a
file name you named before) and press the ENTER key.

PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT: CS950 EEPROM:0

✽   ✽   ✽   ✽   ✽   ✽   ✽  ✽   ✽  ✽   ✽  ✽  ✽   ✽   ✽   ✽   ✽   ✽  ✽  ✽  ✽  ✽  ✽ 

MENU

✽   ✽   ✽   ✽   ✽   ✽   ✽   ✽   ✽   ✽    ✽   ✽   ✽   

Page (1/1)

✽   ✽   ✽  ✽   ✽  

PAL

1. SC FREQUENCY

11.4. 3200K B_PHASE

2. SC FREQUENCY

12.1. 5100K R_GAIN

3.1. LL PHASE1 FOR ACtype (50Hz)

12.2. 5100K B_GAIN

3.2. LL PHASE1 FOR ACtype (50Hz)

12.3. 5100K R_PHASE

4. HI CLIP LEVEL

12.4. 5100K B_PHASE

5. PEDESTAL

13. HIGH LIGHT CHROMA CLIP

6. ALC DC
7.1. VIDEO OUT GAIN (L)
7.2. VIDEO OUT GAIN (H)
8.1. BURST LEVEL R
8.2. BURST LEVEL B
8.3. BURST PHASE R
8.4. BURST PHASE B
9.1. WB 3200K MANU OFFSET R
9.2. WB 3200K MANU OFFSET B
10.1. WB 6500K ATW LIMIT R
10.2. WB 6500K ATW LIMIT B
11.1. 3200K R_GAIN
11.2. 3200K B_GAIN
11.3. 3200K R_PHASE

<CONTENTS>    TD4 17.73447MHz+ – 40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY

LOAD (F1)          QUIT (F3)             SAVE (F5)

After replacing EEPROM (IC5 on the Main Board) with new
part, load the initial data to EEPROM according to the fol-
lowing procedure.

q

Turn the power off of the WV-CS950/WV-CS954E.

w

Short between TD777 on the Servo Board or TD17 on
the Main Board (refer to Wiring Diagram on page 3-1)
and ground.

e

Turn the power on the WV-CS950/WV-CS954E.

r

Make connection according to "3.1. Connection".

t

Insert new floppy disk containing DOS operating System
and the E.V.R. Adjustment Program into the computer
(IBM PC/AT) and turn on the Power Switch of the com-
puter.

y

At the prompt, type RADJ2 CS95E and press the ENTER
key, then the initial menu page will be displayed.

u

Press the LOAD (F1) key of the computer, and the com-
puter will ask you for the file name .

i

Type CS95E.EV2 and press the ENTER key.

o

When finishing the loading, press the QUIT (F3) key.

!0

Press the N key then press the ENTER key.

!1

Type RADJ2 and press the ENTER key.

!2

Type W_E_0 and press the ENTER key. (refer to Fig. 3-
5-1)

!3

Type A5 and press the ENTER key. (refer to Fig. 3-5-1)

!4

Type W_E_01 and press the ENTER key. (refer to Fig. 3-
5-1)

!5

Type 5A and press the ENTER key. (refer to Fig. 3-5-1)

!6

Turn the power off once and on again of the WV-
CS950/WV-CS954E.

!7

Remove the short wire from TD777 on the Servo Board
or TD17 on the Main Board.

!8

Reset the Preset data according to "4.4. Preset Data
Reset Procedure".

!9

Adjust the Camera according to "4.1. Camera
Adjustment", "4.2. Back Focus Adjustment" and "4.3.
Tilt Adjustment" if necessary.

< EVR2 >

W_E_0

N 

!2

EEPROM

000 : XX - A5

N 

!3

< EVR2 >

W_E_01

N 

!4

EEPROM

000 : XX - 5A

N 

!5