Read Panasonic WV-CS950 / WV-CS954E Service Manual online
2-8
(4) Installing E.V.R Adjustment Program
8
Make a copy of following necessory files to your comput-
er from original floppy disk.
er from original floppy disk.
RADJ2.EXE
CS95E.SEQ
CS95AF1.SEQ
CS95TLT.SEQ
CS95PRE.SEQ
CS95E.EV2
8
The Example given here is for A 2 drive computer, your
procedure might vary slightly depending on the drive
configuration.
configuration.
8
Confirm that the contents of CONFIG.SYS file on your
computer is DEVICE=ANSI.SYS (Basic).
computer is DEVICE=ANSI.SYS (Basic).
8
Insert floppy disk containing the E.V.R. Adjustment
Program into your floppy drive (for example,drive:A) and
type A:
Program into your floppy drive (for example,drive:A) and
type A:
8
At the prompt, type CD IBMPC and press ENTER key.
8
Type COPY RADJ2.EXE B: and press ENTER key.
8
Type CD\ and press ENTER key.
8
Type CD SEQ and press ENTER key.
8
Type COPY CS95E.SEQ B: and press ENTER key.
8
Type COPY CS95AF1.SEQ B: and press ENTER key.
8
Type COPY CS95TLT.SEQ B: and press ENTER key.
8
Type COPY CS95PRE.SEQ B: and press ENTER key.
8
Type CD\ and press ENTER key.
8
Type CD EVR and press ENTER key.
8
Type COPY CS95E.EV2 B: and press ENTER key.
8
After completing installation of program, you are ready to
use the E.V.R. Adjustment Program.
use the E.V.R. Adjustment Program.
3.3. Setting Up for Standard Picture
8
The adjustment should be done after 30 minutes warm-
up.
up.
8
Set the Logarithmic Gray Scale Chart.
8
Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray
Scale Chart.
Scale Chart.
8
Aim the Camera at the Logarithmic Gray Scale Chart.
8
Set the Camera by the Remote E.V.R. Adjustment Kit so
that the Logarithmic Gray Scale Chart becoms full pic-
ture on the Underscanned Colour Video Monitor.
that the Logarithmic Gray Scale Chart becoms full pic-
ture on the Underscanned Colour Video Monitor.
8
Adjust the Lens Focus by the Remote E.V.R. Adjustment
Kit to obtain correct focal point.
Kit to obtain correct focal point.
8
The adjustments should be done with this Standard
Picture, unless otherwise specified.
Picture, unless otherwise specified.
8
Set the switch SW3 on the Board to the position as
shown in Fig. 3-2-3.
shown in Fig. 3-2-3.
8
Set the VP/STD.Camera Selection Switch on the Rear
Panel to STD CAMERA position.
(3) Menu Setting
8
Set the Mode Selection Switch on the Front Panel to the
"ALARM OFF" (center) position.
"ALARM OFF" (center) position.
8
Keep pressing the Program Switch for 3 seconds or more
until "Program Menu" is displayed on the monitor screen.
until "Program Menu" is displayed on the monitor screen.
8
Move the cursor to the "Controller Set Up" position by
pressing the Up and Down Switch.
pressing the Up and Down Switch.
8
Display the "Controller Set Up Menu" on the monitor by
pressing the Set Switch.
pressing the Set Switch.
8
Move the cursor to the "Set Up Disable" position by
pressing the Up and Down Switch.
pressing the Up and Down Switch.
8
Change "Disable" to "Enable" by pressing the Set Switch.
8
After completing the above setting, move the cursor to
the Communication position by pressing the Up and
Down Switch.
the Communication position by pressing the Up and
Down Switch.
8
Display the "Communication Menu" on the monitor by
pressing the Set Switch .
pressing the Set Switch .
8
After confirming the Baud Rate is 9600, finish this menu
by pressing the Program Switch twice.
by pressing the Program Switch twice.
<Rear>
<F
ront>
Board
SW3
ON
<SW3>
<SW3>
1 2 3 4
Select switch #2 to ON (PAL) position.
#
ON
OFF
1
FIX
2
NTSC
PAL
3
FIX
4
FIX
Fig. 3-2-3
Click on the first or last page to see other WV-CS950 / WV-CS954E service manuals if exist.