Read Panasonic WV-CP160 Service Manual online
<Adjustment Procedure-2>
(E.V.R. Adjustment)
Insert new disk containing the E.V.R. Adjustment pro-
gram into IBM PC/AT.
At the prompt, type RADJ CP160E and press the ENTER
key, an initial menu will be displayed in Table 5-1.
gram into IBM PC/AT.
At the prompt, type RADJ CP160E and press the ENTER
key, an initial menu will be displayed in Table 5-1.
Press the SAVE(F5) key of the Computer, then the
Computer will ask you for the file name.
Give appropriate file name to the Computer. But do not
use CP160E.EVR for your file.
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
Press the LOAD(F1) key and type CP160E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
Computer will ask you for the file name.
Give appropriate file name to the Computer. But do not
use CP160E.EVR for your file.
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
Press the LOAD(F1) key and type CP160E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
1. Subcarrier Frequency Adjustment
Menu:
1. SC FREQUENCY
Test Point:
TD801 or TD802 (SC VCXO)
Main Board
Connect the Frequncy Counter to TD801 or TD802.
Adjust data with the ARROW keys so that the Subcarrier
Frequency becomes 17.73447 MHz ± 40 Hz.
Press the ENTER key for next adjustment.
Adjust data with the ARROW keys so that the Subcarrier
Frequency becomes 17.73447 MHz ± 40 Hz.
Press the ENTER key for next adjustment.
2. High Clip Adjustment
Menu:
2.HI CLIP LEVEL
Test Point:
CN2 (Video Output Terminal)
VP Board
Change the Colour Temperature from 5100K to 3200K by
mounting the Colour Conversion Filter W12 on the Lens.
Aim the Camera at the Logarithmic Gray Scale Chart.
Connect the Oscilloscope to the Video Output Terminal.
Open the Lens Iris fully.
Adjust data with the ARROW keys so that the signal level
becomes 805 mV as shown in Fig. 5-2.
mounting the Colour Conversion Filter W12 on the Lens.
Aim the Camera at the Logarithmic Gray Scale Chart.
Connect the Oscilloscope to the Video Output Terminal.
Open the Lens Iris fully.
Adjust data with the ARROW keys so that the signal level
becomes 805 mV as shown in Fig. 5-2.
Table 5-1
– 6 –
WV-CP160
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CP160 EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1. SC FREQUENCY
2. HI CLIP LEVEL
3. ALC DC
4. VIDEO OUT GAIN
5. PEDESTAL
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.3. 3200K MATRIX
10.1. 5100K R_GAIN
10.2. 5100K B_GAIN
11. HI LIGHT CHROMA CLIP
<CONTENTS>
2. HI CLIP LEVEL
3. ALC DC
4. VIDEO OUT GAIN
5. PEDESTAL
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.3. 3200K MATRIX
10.1. 5100K R_GAIN
10.2. 5100K B_GAIN
11. HI LIGHT CHROMA CLIP
<CONTENTS>
17734470 + - 40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
805 mV
+ 35
– 0
– 0
Fig. 5-2
Press the ENTER key for next adjustment.
3. ALC DC Adjustment
Menu:
3. ALC DC
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Logarithmic Gray Scale Chart.
Open the Lens Iris.
Adjust data with the ARROW keys so that the measure
level becomes 00 and 05.
Press the ENTER key for next adjustment.
Aim the Camera at the Logarithmic Gray Scale Chart.
Open the Lens Iris.
Adjust data with the ARROW keys so that the measure
level becomes 00 and 05.
Press the ENTER key for next adjustment.
4. Video Out Gain Adjustment
Menu:
4. VIDEO OUT GAIN
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Logarithmic Gray Scale Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the Video sig-
nal level becomes 700 ± 50 mV as shown in Fig. 5-3.
Aim the Camera at the Logarithmic Gray Scale Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the Video sig-
nal level becomes 700 ± 50 mV as shown in Fig. 5-3.
Fig. 5-3
700
±
50 mV
5. Pedestal Adjustment
Menu:
5. PEDESTAL
Test Point:
CN2 (Video Output Terminal)
VP Board
Connect the Oscilloscope to the Video Output Terminal.
Close the Lens Iris.
Adjust data with the ARROW keys so that the Pedestal
level becomes 50 ± 5 mV as shown in Fig. 5-4.
Close the Lens Iris.
Adjust data with the ARROW keys so that the Pedestal
level becomes 50 ± 5 mV as shown in Fig. 5-4.
Press the ENTER key for next adjustment.
+35
–0
Click on the first or last page to see other WV-CP160 service manuals if exist.