WV-CP160 - Panasonic Video Monitoring Service Manual (repair manual)

wv-cp160 service manual
Model
WV-CP160
Pages
26
Size
927.55 KB
Type
PDF
Document
Service Manual
Brand
Device
Video Monitoring / CAMERA
File
wv-cp160.pdf
Date

Read Panasonic WV-CP160 Service Manual online

ORDER NO. AVS0006268C8
C
2 0 0 0     M a t s u s h i t a   C o m m u n i c a t i o n   I n d u s t r i a l   C o . ,   L t d .
A l l   r i g h t s   r e s e r v e d .   U n a u t h o r i z e d   c o p y i n g   a n d
d i s t r i b u t i o n   i s   a   v i o l a t i o n   o f   l a w .
Colour CCTV Camera
WV-CP160
Super Dynamic
SPECIFICATIONS
Pick-up Device:
752 (H) x 582 (V) pixels, Interline Transfer CCD
Scanning Area:
4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)
Scanning:
625 lines/50 fields/25 frames
Horizontal:
15.625 kHz
Vertical:
50 Hz
Synchronization:
Multiplexed Vertical Drive (VD2) by use of specified camera drive unit.
Video Output:
1.0 V[p-p] PAL composite 75 
/through camera drive unit
Horizontal Resolution:
480 lines
Signal-to-Noise Ratio:
50 dB (AGC OFF, weight ON)
Dynamic Range:
48 dB
Minimum Illumination:
0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx (0.08 footcandle) at F1.4]
Gain Control:
AGC ON or OFF (SET UP MENU) selectable
White Balance:
ATW or AWC (SET UP MENU) selectable
Aperture:
Set Variable (SET UP MENU) Sharp-Soft selectable by detail level selector
Electronic Light Control:
ALC/ELC
Super Dynamic
2
:
ON or OFF (SET UP MENU) selectable
Electronic Shutter Speed:
1/50 (OFF), 1/120 1/250, 1/500, 1/1000 1/2000, 1/4000, 1/10000s selectable
Lens Mount:
CS-mount
ALC Lens:
DC drive
Ambient Operating Temperature:
–10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity:
Less than 90 %
Power Source:
From the specified monitor or camera drive unit
Power Consumption:
350 mA
Dimensions (without lens):
68 (W) x 65 (H) x 126 (D) mm
[2-11/16” (W) x 2-9/16” (H) x 4-15/16” (D)]
Weights (without lens):
0.375 k
g
(0.8  lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
(Lens: Option)
WV-CP160
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
!
WARNING
STANDARD ACCESSORIES
Body Cap................................................................................1 pc.
Camera Mounting Bracket......................................................1 pc.
OPTIONAL ACCESSORIES
Lenses :
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, 
WV-LA210C3, WV-LA408C3, WV-LA908C3, 
WV-LZ61/10, WV-LZ61/15, WV-LZ62/2, WV-
LZ62/8
CONTENTS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS............................................................................... 1
ADJUSTMENT PROCEDURE ................................................................................................................................. 2
LOCATION OF TEST POINTS AND ADJUSTING CONTROLS........................................................................... 11
WIRING DIAGRAM ................................................................................................................................................ 12
SCHEMATIC DIAGRAM 
SENSOR BOARD .............................................................................................................................................. 13
VP BOARD......................................................................................................................................................... 14
MAIN BOARD..................................................................................................................................................... 17
I/F BOARD ......................................................................................................................................................... 18
CONDUCTOR VIEW
SENSOR BOARD .............................................................................................................................................. 13
VP BOARD......................................................................................................................................................... 15
MAIN BOARD..................................................................................................................................................... 16
I/F BOARD ......................................................................................................................................................... 18
EXPLODED VIEW ...................................................................................................................................................19 
REPLACEMENT PARTS LIST  ............................................................................................................................. 20
WV-CP160
– 1 –
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q
Auto Iris Lens Connector
This connector is used to connect the auto iris lens. It sup-
plies power and DC control signal to the auto iris lens.
w
Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture
focus by rotating it.
e
Lens (Option)
r
Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting
bracket.
t
Focus Fixing Screw
y
Down Button (
)
This button is used to move the cursor downward.  It is also
used to select items in the CAM SET UP menu.
u
Right Button (
)
This button is used to move the cursor to the right.  It also
selects the mode and can be used to adjust some levels.
i
Left Button (
)
This button is used to move the cursor to the left.  It also
selects the mode and can be used to adjust some levels.
o
Up Button (
)
This button is used to move the cursor upward. It is also
used to select items in the CAM SET UP menu.
!0
Set Button (
)
This button is used to activate an item selected in the CAM
SET UP menu.
!1 
Selector (NC)
This selector is not used on this camera.
!2
Detail Level Selector (SOFT-SHARP)
This selector is used to select the detail / aperture level as
follows.
SOFT: When a quad system is connected to this camera, 
select this position.
SHARP: Select this position usually.
!3
Microphone Selector (MIC OFF-ON)
Select ON or OFF as needed.
!4
Microphone
!5
Power Indicator
This indicator lights up when the power of this camera is
on.
!6
Monitor Output Connector (MONITOR OUT)
This connector is used to connect with the video input con-
nector of the monitor.
!7
Video Output Terminal
This terminal is used to connect with the video input con-
nector of the monitor.
!8
Rear Cover
The rear cover can be removed to gain access to the temi-
nal.
Super Dynamic
Super Dynamic
WV-
 
G
P160
CP160
MONITOR OUT
NC
MIC OFF-ON
SOFT-SHARP
LOCK
q t
y
!3
!0
o u
i
w
r
e
!5
!8
!4
!1
!2
!6
!7
Rear Panel
Open the panel to the upper left until it stops by rotating counterclockwise.
ADJUSTMENT PROCEDURE
1. Test Equipment Required
The following test equipment are required for adjustment
of  the Colour CCTV Camera WV-CP160.
Oscilloscope
Frequency Counter
Waveform Monitor
Vectorscope
Underscanned Colour Video Monitor
Camera Drive Unit (WV-PS11B or WV-PS104C)
12 V DC Power Supply Unit
Personal Computer (IBM PC/AT type or equivalent)
Standard Straight RS-232C Cable
ALC Lens (WV-LA9C3A, WV-LA9C3B or equivalent)
Lux Meter
Lighting (275 footcandles (2,750 ± 150 lux), Colour
Temperature 5,100 ± 100 K)
Colour Temperature Conversion Filters
(KENKO: W12, C4 or equivalent)
Radiation Chart
Logarithmic Gray Scale Chart. 
(Part Number:YWV2310RB99) 
Extension Cable as shown in Fig. 1-1.
(Part Number: YWV0EA1171AN) 
Make a conversion cable as follows.
Fig. 1-2
Remote Electric Variable Resistor (E. V. R.) kit as shown in
Fig. 1-2. (Part Number: YWV0EA1174AN) 
Fig. 1-3
13
12
11
10
9
8
7
6
5
4
3
2
1
26
25
24
23
22
21
20
19
18
17
16
15
14
GND
T (B)
R (B)
To
E. V. R.
Kit
To PC
Via RS-232C
Cable
2. Disassembling Procedure for
Adjustment
Referring to Fig. 2-1, remove two screws that secure the
Mount Adaptor and remove the Mount Adaptor.
Referring to Fig. 2-2, remove two screws that secure the
Main Cover and remove the Main Cover.
Remove one screw that secure the Rear Cover and
remove the Rear Cover.
Remove two screws
Mount Adaptor
Fig. 2-1
Fig. 2-2
Remove two screws
Main Cover
– 2 –
WV-CP160
Fig. 1-1
To 
Main Board 
CN404
To 
VP Board 
CN1
CN3
CN2
Remove
one screw
Rear Cover
Page of 26
Display

Download Panasonic WV-CP160 Service Manual (Repair Manual)

Here you can read online and download Panasonic WV-CP160 Service Manual in PDF. WV-CP160 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Panasonic WV-CP160 Video Monitoring. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.