Read Panasonic WV-CP160 Service Manual online
WV-CP160
– 8 –
6.2. Burst Level Adjustment
Menu:
6.2. BURST LEVEL
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes –
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes –
α
from noted data.
Press the ENTER key for next adjustment.
6.3. Burst Level Adjustment
Menu:
6.3. BURST LEVEL
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes –
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes –
α
from noted data.
Press the ENTER key for next adjustment.
6.4. Burst Level Adjustment
Menu:
6.4. BURST LEVEL
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes +
Aim the Camera at the Colour Chip Chart.
Connect the Oscilloscope to the Video Output Terminal.
Adjust data with the ARROW keys so that the data
becomes +
α
from noted data.
Press the ENTER key and ROLL DOWN Key to confirm
Burst Level, Phase and Red Vector position within the
specification as shown in Fig. 5-5, 5-6 , 5-7 and Table 5-2.
Burst Level, Phase and Red Vector position within the
specification as shown in Fig. 5-5, 5-6 , 5-7 and Table 5-2.
Phase
Gain
Red
104
±
2
°
220
±
5 %
Yellow
165
±
5
°
120
±
5 %
Fig. 5-7
Table 5-2
Repeat adjustment steps 6.1 to 6.4 until Burst Level,
Phase and Red Vector position are adjusted to proper
position.
Press the ENTER key for next adjustment.
Phase and Red Vector position are adjusted to proper
position.
Press the ENTER key for next adjustment.
cy
g
M
G
Y
L
yl
B
b
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
mg
r
20%
20%
dG
7.1. White Balance 3200K Manual
Offset R Adjustment
Menu:
7.1. WB 3200K MANU OFFSET R
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the White Chart or White Paper.
Set the Gain Control of the Vectorscope to maximum.
Adjust data with the ARROW keys so that the vector posi-
tions at the center of the Vectorscope as shown in Fig.5-8.
Aim the Camera at the White Chart or White Paper.
Set the Gain Control of the Vectorscope to maximum.
Adjust data with the ARROW keys so that the vector posi-
tions at the center of the Vectorscope as shown in Fig.5-8.
cy
g
M
G
Y
L
yl
B
b
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
mg
r
20%
20%
dG
Positions at center.
Fig. 5-8
7.2. White Balance 3200K Manual
Offset B Adjustment
Menu:
7.2. WB 3200K MANU OFFSET B
Test Point:
CN2 (Video Output Terminal)
VP Board
Keep the Colour Temperature at 3200K.
Aim the Camera at the White Chart or White Paper.
Set the Gain Control of the Vectorscope to maximum.
Adjust data with the ARROW keys so that the vector posi-
tions at the center of the Vectorscope as shown in Fig.5-9.
Aim the Camera at the White Chart or White Paper.
Set the Gain Control of the Vectorscope to maximum.
Adjust data with the ARROW keys so that the vector posi-
tions at the center of the Vectorscope as shown in Fig.5-9.
Press the ENTER key for next adjustment.
cy
g
M
G
Y
L
yl
B
b
G
C
Y
dG
10
°
0
°
10
°
dø
100%
75%
R
V
U
mg
r
20%
20%
dG
Positions at center.
Fig. 5-9
Repeat adjustment steps 7.1 and 7.2 until vector posi-
tions at the center of the Vectorscope.
Press the ENTER key for next adjustment.
tions at the center of the Vectorscope.
Press the ENTER key for next adjustment.
Click on the first or last page to see other WV-CP160 service manuals if exist.