Read JBL SUB 250P (serv.man2) EMC - CB Certificate online
Page 53 of 57
Report No.: 11034065 001
IEC 60065 ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
19.201.2 Restraining device
19.201.2.1 Television receivers should be
provided with a restraining device such as a fixing
point to facilitate restraining the television from
toppling forward.
provided with a restraining device such as a fixing
point to facilitate restraining the television from
toppling forward.
19.201.2.2 Where a restraining device is provided
in accordance with 19.201.2.1 information shall
be provided in the instructions for installation or
use, to ensure correct and safe installation. Such
information should also be provided as a label on
the television receiver. Any such restraining
device shall be capable of withstanding a pull of
100 N in all directions without damage.
in accordance with 19.201.2.1 information shall
be provided in the instructions for installation or
use, to ensure correct and safe installation. Such
information should also be provided as a label on
the television receiver. Any such restraining
device shall be capable of withstanding a pull of
100 N in all directions without damage.
19.201.3 Glass slide test ǂ
Television receivers and display devices that may
be used for television purposes, with a mass of
18 kg or more, are placed on a clean, dry, glass
covered horizontal surface such that only the
supporting feet are in contact with the glass. The
glass-covered surface is then tilted in the most
unfavourable direction through an angle of 10°.
be used for television purposes, with a mass of
18 kg or more, are placed on a clean, dry, glass
covered horizontal surface such that only the
supporting feet are in contact with the glass. The
glass-covered surface is then tilted in the most
unfavourable direction through an angle of 10°.
During the tests, the equipment shall not slide.
ǂ Clause 19.201.3 forms part of the Standard on
31 January 2013.
31 January 2013.
20
Delete the following paragraph:
'The requirements are considered to be fulfilled if
the apparatus complies with the requirements of
20.1 and 20.2' and replace with
the apparatus complies with the requirements of
20.1 and 20.2' and replace with
'The requirements are considered to be fulfilled if
the apparatus complies with the requirements of
20.1 and 20.2. Alternatively the requirements are
considered to be fulfilled if the apparatus
complies with the requirements of Clause
20.201.'
the apparatus complies with the requirements of
20.1 and 20.2. Alternatively the requirements are
considered to be fulfilled if the apparatus
complies with the requirements of Clause
20.201.'
N/A
Table 21
In the third and fourth columns delete ' HB75' and
'No requirement' and replace both with 'V-1 '.
'No requirement' and replace both with 'V-1 '.
N/A
20.2.3
After Clause 20.2.3, add the following variation:
20.201 Resistance to fire-Alternative tests
20.201.1 General
Parts of non-metallic material shall be resistant to
ignition and the spread of fire.
ignition and the spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
a) Components that are contained in an
enclosure having a flammability category of V-0
according to AS/NZS 60695.11.10 and having
openings only for the connecting wires filling the
enclosure having a flammability category of V-0
according to AS/NZS 60695.11.10 and having
openings only for the connecting wires filling the
N/A
Click on the first or last page to see other SUB 250P (serv.man2) service manuals if exist.