Read Harman Kardon SIGNATURE 2.0 (serv.man13) User Guide / Operation Manual online
Remote Contr
ol Operation
10
Signature 2.0
m
Bass Boost:
When the button is pressed a menu will
appear on the screen (see figure OSD-20 on page 34) and
you may boost the bass frequency level by pressing the
you may boost the bass frequency level by pressing the
‹
or
›
Menu Control
i
. When you have completed
the adjustment, press again to enter the setting and
remove the menu from the screen.
remove the menu from the screen.
n
Balance Control:
When the button is pressed a
diagram will appear on the screen (see figure OSD-9 on
page 26) that shows a small circle as the current listening
position. To adjust front/back fade and left/right balance
use all four
page 26) that shows a small circle as the current listening
position. To adjust front/back fade and left/right balance
use all four
Menu Control
buttons
i
to “move” the
listening position with respect to the center of the room.
Press again to enter the setting and remove the diagram
from the screen.
Press again to enter the setting and remove the diagram
from the screen.
o
Center Mode:
When the button is pressed a menu
will appear on the screen (see figure OSD-22 on page 35)
and you may then make a selection using
and you may then make a selection using
‹
or
›
Menu
Control
i
. Press again to enter the setting and remove
the menu from the screen.
p
Surround Control:
When the button is pressed a
menu will appear on the screen (see figure OSD-23 on
page 35) and you may then make a selection using
page 35) and you may then make a selection using
‹
or
›
Menu Control
i
. Turning the surround channel
off with this control will change the setting only until the
source is changed, at which point the setup configuration
selected in the
source is changed, at which point the setup configuration
selected in the
Spkr Setup Menu
will take effect.
Press again to enter the setting and remove the menu from
the screen.
the screen.
IMPORTANT NOTE: Adjustments made using
Treble
Cut
,
Subwoofer Trim
,
Bass Boost
,
Balance Control
,
Center Mode
and
Surround Control
buttons
k l
m n o p
are temporary. When the mode or input
source is changed, or the 2.0 is turned off, the adjustment
is canceled and the system preset will return. To make a
permanent change to any of these settings, use the
is canceled and the system preset will return. To make a
permanent change to any of these settings, use the
Effects Menu
, as described on page 25.
q
TV Volume:
Control the volume of a TV or other
audio device not connected to the 2.0. When shipped
from the factory, the buttons will control television sets
with the popular RC-5 remote code system. To use these
buttons to control other television sets you must program
the codes into the remote as described on page 29.
from the factory, the buttons will control television sets
with the popular RC-5 remote code system. To use these
buttons to control other television sets you must program
the codes into the remote as described on page 29.
r
Main Volume Control:
Control the unit’s volume.
All channels are controlled simultaneously.
s
Mute:
Press to temporarily silence audio output.
Press again to return to previous volume level.
t
Transport Controls:
These buttons may be
programmed to control the transport functions of
compatible VCR’s, DVD player, CD player, cassette decks,
and other source equipment by following the instructions
on pages 12 and 13. As shipped from the factory, the
remote will control compatible Harman Kardon CD
players and cassette decks when
compatible VCR’s, DVD player, CD player, cassette decks,
and other source equipment by following the instructions
on pages 12 and 13. As shipped from the factory, the
remote will control compatible Harman Kardon CD
players and cassette decks when
CD
or
Tape Source
Selection
g
have been pressed. Some of these buttons
also have specific functions to operate the 2.0’s tuner
when it is selected.
when it is selected.
a) The
‡
and
·
buttons are used for seek tuning.
Each press will cause the tuner to search for the station
with the next higher or lower frequency that has a
signal strong enough for acceptable reception.
with the next higher or lower frequency that has a
signal strong enough for acceptable reception.
b) The
‚
and
—
buttons may be used to
manually tune stations in single frequency increments
or, by pressing and holding one of these buttons, it is
possible to quickly tune to a specific station.
or, by pressing and holding one of these buttons, it is
possible to quickly tune to a specific station.
The + and - buttons:
a) When
CD
is selected and the unit is a CD changer,
these buttons will change to the next disc
∏
or
previous disc
Â
.
Click on the first or last page to see other SIGNATURE 2.0 (serv.man13) service manuals if exist.