Read Harman Kardon SIGNATURE 2.0 (serv.man13) User Guide / Operation Manual online
Remote Contr
ol Pr
ogramming
13
Signature 2.0
All other keys may only be programmed with one remote
code. The code contained in these keys remains the same
regardless of the source selection.
code. The code contained in these keys remains the same
regardless of the source selection.
WARNING: These keys transmit codes that are vital to
the operation of the product. It is not recommended that
they be programmed with alternative codes, as it may
then be impossible to operate certain functions:
the operation of the product. It is not recommended that
they be programmed with alternative codes, as it may
then be impossible to operate certain functions:
Menu
All Menu Navigation Buttons
‹ ›
⁄¤
Enter
All Mode Selectors
Treble
Sub
Center
Bass
Balance
Surr
Mute
Simulcast
To program the remote, follow these steps. Note that it is
not necessary to program all keys, only those that are
required to operate the subject device. Keys not
programmed retain codes preprogrammed at the factory.
not necessary to program all keys, only those that are
required to operate the subject device. Keys not
programmed retain codes preprogrammed at the factory.
1. Slide
Use/Learn
e
at the top left corner of the remote
to the right so that it is next to
Learn
.
2. If one of the multifunction buttons is being
programmed press the source button (e.g.,
programmed press the source button (e.g.,
CD
,
Vid 1
) you
wish to have this function associated with. If you are
programming a single function key, proceed to the next
step.
programming a single function key, proceed to the next
step.
3. Press the button on the remote that is to be
programmed. The
programmed. The
Learning LED
b
will illuminate.
4. Place the 2.0’s remote head to head with the other
remote control whose function is being learned. The two
remotes should be no more than 20cm apart.
remote control whose function is being learned. The two
remotes should be no more than 20cm apart.
5. Press and hold the button on the other remote
corresponding to the function to be memorized until the
corresponding to the function to be memorized until the
Learning LED
starts to blink. When the LED goes out,
release the button on the transmitting remote. The
function code has been successfully captured by the 2.0’s
remote.
function code has been successfully captured by the 2.0’s
remote.
NOTE: If both LEDs
b d
flash during a
programming operation, it indicates that the remote’s
memory is full or that the remote codes from the
transmitting remote are not compatible with the unit’s
signal format.
memory is full or that the remote codes from the
transmitting remote are not compatible with the unit’s
signal format.
6. Continue to program any additional remote commands
using steps 2 through 5. When you have finished
programming the remote, slide
using steps 2 through 5. When you have finished
programming the remote, slide
Use/Learn
e
to the left
so that it is in the
Use
position.
Resetting the Remote Memory
Codes for a new device may be programmed “over”
codes previously programmed. It is also possible to reset
the memory for individual keys, or for the entire remote.
When a memory position is reset, the remote will return
to the original factory preset command.
codes previously programmed. It is also possible to reset
the memory for individual keys, or for the entire remote.
When a memory position is reset, the remote will return
to the original factory preset command.
To reset the memory for a specific key, put
Use/Learn
in
the
Learn
position. Press
Main Power Off
a
and the
button to be reset at the same time.
Sending
and
Learning
indicators will light momentarily. When the
lights go out, the memory has been cleared of the user
programmed code and reset to the factory preset. Return
programmed code and reset to the factory preset. Return
Use/Learn
e
to the
Use
position when finished.
To return all keys to their factory preset commands first
put
put
Use/Learn
e
in the Learn position. Then press
Main Power On
a
and confirm that the
Learn LED
b
has illuminated. While continuing to press
Main
Power On
, press and hold
Main Power Off
a
until the
Learn LED
goes off for about 3 seconds. It will then
blink twice. Then release the two buttons. The memory
has been cleared of any user programmed commands and
the original commands have been restored. Slide
has been cleared of any user programmed commands and
the original commands have been restored. Slide
Use/Learn
e
back to the
Use
position to return to
normal operation.
Click on the first or last page to see other SIGNATURE 2.0 (serv.man13) service manuals if exist.