Read Harman Kardon SIGNATURE 2.0 (serv.man13) User Guide / Operation Manual online
Remote Contr
ol Pr
ogramming
12
Signature 2.0
Remote Control Programming
This powerful remote control will operate the 2.0, as well
as most CD players and tape decks manufactured by
Harman Kardon. If your equipment requires different
codes, it may be programmed to copy the codes from
most infrared remotes.
as most CD players and tape decks manufactured by
Harman Kardon. If your equipment requires different
codes, it may be programmed to copy the codes from
most infrared remotes.
Loading Batteries
The life of the batteries for the remote control is about
one year in normal operation. If the amber
one year in normal operation. If the amber
Sending LED
d
does not flash when remote buttons are pushed, that
is an indication that the batteries need to be replaced.
To change the batteries:
1. Remove the back cover by sliding it in the direction of
the arrow.
the arrow.
2. Remove the old batteries and insert fresh AAA type
cells. Be certain to observe the correct polarity by noting
the (
cells. Be certain to observe the correct polarity by noting
the (
∏
) and (
Â
) marks on both the inside of the case and
on the battery cells. It is recommended that both batteries
be changed at the same time.
be changed at the same time.
3. Close the cover until it clicks shut.
NOTE: It is important that the batteries be replaced
within ten minutes after the old batteries are removed
to avoid losing any remote codes that have been
programmed into the remote’s memory.
within ten minutes after the old batteries are removed
to avoid losing any remote codes that have been
programmed into the remote’s memory.
Remote Control Range
The remote will operate at a range of up to 5 meters from
the unit, when the batteries are fully charged. The remote
will also operate at an angle of up to 30° to either side of
the unit.
the unit, when the batteries are fully charged. The remote
will also operate at an angle of up to 30° to either side of
the unit.
Always point the remote transmitter at the front of the
unit. If you find that remote commands are not being
received, it may be necessary to use a remote IR sensor.
unit. If you find that remote commands are not being
received, it may be necessary to use a remote IR sensor.
Programmable Keys
Many buttons may be programmed to new functions to
operate virtually any component in your system. Ten
CANNOT be programmed with a new code, as they
control high-level functions of the 2.0. These keys are
operate virtually any component in your system. Ten
CANNOT be programmed with a new code, as they
control high-level functions of the 2.0. These keys are
Main Power On
,
Main Power Off
, and the eight source
input keys:
TV
,
Vid 1
,
Vid 2
,
Vid 3
,
Tuner
,
CD
,
Tape
and
Aux
.
Some keys may be programmed with a separate function
for each input. Thus, these keys may change their code
when the input source is changed. (e.g.,
for each input. Thus, these keys may change their code
when the input source is changed. (e.g.,
Play
may
transmit a different code when
CD
is selected as when
VCR
is selected.) These keys may be programmed with
multiple codes:
All Numeric Keys (
0
–
9
)
Source Power On
Source Power Off
Stop
■
Disc/Track
Record
●
Pause
❙❙
∏
(Plus)
Â
(Minus)
Tune Up/Down
››
/
‹‹
Skip Up/Down
›
/
‹
Play Forward/Reverse
›
/
‹
TV Volume Up/Down
Display
Store
RDS
Type
Presets
Mute
Tune
Surround
Source
2.0
Standby
On/Off
DVD Vol
Dolby
Dig
ital 10
Click on the first or last page to see other SIGNATURE 2.0 (serv.man13) service manuals if exist.