Read Sony HDR-PJ800 / HDR-PJ810 / HDR-PJ810E / HDR-PJ820 / HDR-PJ820E (serv.man2) Service Manual online
1-8
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
– ENGLISH –
(17) Remove the two screws and remove the two bosses to detach the
Sheet Metal (A).
Peel off the Polyimide Sheet.
TO
P
FRON
T
Sheet Metal (A)
Bosses
Polyimide Sheet
Screw
Screw
(18) Disconnect the connector and peel off the adhesive part of the LF-
2063 Flexible Board.
TOP
FRON
T
Adhesive part
Connector
LF-2063 Flexible Board
(19) Remove the two screws and remove the CM-1007 Board, Seal
Rubber, Optical Filter Block from the Lens Device (LSV-1400B).
TO
P
FRONT
Screw
Screw
Optical Filter Block
Seal Rubber
CM-1007 Board
Lens Device (LSV-1400B)
Installation
(1) Install the Optical Filter Block, Seal Rubber, CM-1007 Board to the
Lens Device (LSV-1400B), and then tighten two screws in the order
shown in the figure below.
shown in the figure below.
Tightening torque = 0.13 ± 0.01N · m (1.3 ± 0.1kg f · cm)
Note :
2
1
Optical Filter Block
(Note)
(Note)
Optical Filter Block
Refer to“Assembly-3: How to distinguish the side of
Optical Filter Block facing to Lens Device.”.
Optical Filter Block facing to Lens Device.”.
TOP
FRONT
Screw
Screw
Seal Rubber
CM-1007 Board
Lens Device (LSV-1400B)
(2) Connect the connector of the LF-2063 Flexible Board and stick the
adhesive part of the Flexible Board.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
TO
P
FRONT
Adhesive part
Connector
LF-2063 Flexible Board
LF-2063 Flexible Board
Shape and sticking position
of the Adhesive Sheet
of the Adhesive Sheet
Adhesive Sheet
(3) Stick the Polyimide Sheet.
While attaching the two bosses, install the Sheet Metal (A), and then
tighten two screws in the order shown in the figure below.
tighten two screws in the order shown in the figure below.
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
TOP
FRONT
2
1
Sheet Metal (A)
Bosses
Polyimide Sheet
Screw
Screw
(4) Stick the adhesive part of the LF-2026 Flexible Board to the Sheet
Metal (D-Sub) while positioning it with the two holes.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
Holes
Shape and sticking position
of the Adhesive Sheet
of the Adhesive Sheet
Adhesive Sheet
Adhesive part
LF-2026 Flexible Board
LF-2026 Flexible Board
Sheet Metal (D-Sub)
(5) Connect the connector of the Flexible Board of the Lens Device
(LSV-1400B).
Install the LF-2026 Flexible Board, Sheet Metal (D-Sub).
TOP
FRONT
Connector
Flexible Board of the Lens Device (LSV-1400B)
Sheet Metal (D-Sub),
LF-2026 Flexible Board
LF-2026 Flexible Board
(6) While attaching the boss and the claw, install the Front Ornament,
and then tighten three screws in the order shown in the figure below.
Screw (A)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
1
2
3
TO
P
FR
ONT
Boss
Claw
Screw (B)
Screw (B)
Screw (A)
Front Ornament
Click on the first or last page to see other HDR-PJ800 / HDR-PJ810 / HDR-PJ810E / HDR-PJ820 / HDR-PJ820E (serv.man2) service manuals if exist.