Read Sony SAL70200G2 Service Manual online
2-23
SAL70200G2 (2.8/70-200 G SSM Ⅱ) (70-200mm F2.8 G SSM II)
HELP44
Selection of 4th guide roller (4th lens barrel)
1. Install the 4th guide roller of which diameter is smaller by 1-size than the dimension described on the outer tube and confirm that the
1. Install the 4th guide roller of which diameter is smaller by 1-size than the dimension described on the outer tube and confirm that the
4th lens barrel moves smoothly (operation feeling) without play.
4th Guide
Roller
Roller
Outer Tube
4th cam groove
4th Guide
Roller
Roller
4th Lens Block
Guide Pin
Guide Pin
4th Lens Block
Guide Pin
Guide Pin
Location of description
of 4th cam groove
dimension
of 4th cam groove
dimension
In case of OK : The selection is finished.
In case of NG : Proceed to step 2.
2. Re-assemble the 4th lens barrel at the position where it is rotated 180º with respect to the outer tube in the arrow direction and confirm
the operation feeling.
4th Guide
Roller
Roller
4th Guide
Roller
Roller
4th Lens Block
Guide Pin
Guide Pin
4th Lens Block
Guide Pin
Guide Pin
Outer Tube
4th Lens Barrel
In case of OK : The selection is finished.
In case of NG : If the operation feeling is better than in step 1, proceed to step 3.
In case of NG : If the operation feeling is worse than in step 1, turn back the 4th lens barrel 180º with respect to the outer tube and
proceed to step 3.
3. Select the 4th guide roller of which diameter is smaller than the described dimension by 2 size.
HELP45
Adhesive bond (B-40): J-6082-614-A
Adhesive bond (LOCTITE 460)
Note:
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or the equivalent
Do not use the instant glue that becomes white when dried.
Grease (G-85): J-6082-626-A
1. Install the rear light shield barrel to the mount and tighten it with three screws to which tips two drops of adhesive bond (B-40) are
applied.
Apply the adhesive
bond (B-40)
bond (B-40)
Mount
Rear Light
Shield Barrel
Shield Barrel
2. Apply two drops of adhesive bond (LOCTITE 460) to the tip of stopper screw and tighten the stopper screw.
3. Apply the grease (G-85) to the indicated portion of mount.
4. Install the lens mount block to the outside barrel, apply two drops of adhesive bond (LOCTITE 460) to the tips of four screws and
3. Apply the grease (G-85) to the indicated portion of mount.
4. Install the lens mount block to the outside barrel, apply two drops of adhesive bond (LOCTITE 460) to the tips of four screws and
tighten the screws.
Note:
Note:
Fix the flexible BL PWB and lead wires to the grooves of outside barrel at two locations, threading through the outer diameter. And fix them
with two polyester tapes (black) 10mm.
Apply the adhesive
bond (B-40)
bond (B-40)
Apply the adhesive
bond (B-40)
bond (B-40)
Apply the adhesive
bond (LOCTITE 460)
bond (LOCTITE 460)
Apply the
grease (G-85)
grease (G-85)
Back side of mounting
claw 3 locations
claw 3 locations
Stopper Screw
Outside Barrel
Polyester Tape
(Black) 10mm
(10X50mm)
(Black) 10mm
(10X50mm)
Polyester Tape
(Black) 10mm
(10X50mm)
(Black) 10mm
(10X50mm)
Lead wires
Flexible BL
PWB
PWB
Groove
Click on the first or last page to see other SAL70200G2 service manuals if exist.