Read Sony HBD-N7100W / HBD-N7100WL / HBD-N8100W / HBD-N9100W / HBD-N9100WL / HBD-N9150W / HBD-N9150WL / HBD-N9900SH Service Manual online
HBD-N7100W/N7100WL/N8100W/N9100W/N9100WL/N9150W/N9150WL/N9900SH
4
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
IMPORTANT NOTICE FOR OPERATION CHECK
Before performing an operation check on this model, make sure
you fi rst attach slide door to prevent the laser beam from shining
directly into the eyes.
Additionally, before disassembling this model, make sure you re-
move the power cord and confi rm that no electricity is fl owing
through this model.
Before performing an operation check on this model, make sure
you fi rst attach slide door to prevent the laser beam from shining
directly into the eyes.
Additionally, before disassembling this model, make sure you re-
move the power cord and confi rm that no electricity is fl owing
through this model.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
In order to perform the operation checking, all the units contained
in this unit are needed.
ERATION
In order to perform the operation checking, all the units contained
in this unit are needed.
ABOUT THE LENS CLEANING
Don’t do the lens cleaning with the cotton bud etc. It causes the
trouble.
Don’t do the lens cleaning with the cotton bud etc. It causes the
trouble.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the system.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Touch the [
x
] sensor, press the [
Z
] button simultaneously and
hold down until “D. OFF” displayed on the fluorescent indica-
tor tube (around 5 seconds).
tor tube (around 5 seconds).
Note: When “D. LOCK” is displayed, the disc tray lock is not released by
turning power on/off with the [?/1] button.
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
• Switching
regulator
C201, C207, C402
C402
C207
C201
800
:/2 W
(for C402)
800
:/2 W
(for C201, C207)
– SWITCHING REGULATOR (Component Side) –
slide door
Click on the first or last page to see other HBD-N7100W / HBD-N7100WL / HBD-N8100W / HBD-N9100W / HBD-N9100WL / HBD-N9150W / HBD-N9150WL / HBD-N9900SH service manuals if exist.