Read Sony HBD-N7100W / HBD-N7100WL / HBD-N8100W / HBD-N9100W / HBD-N9100WL / HBD-N9150W / HBD-N9150WL / HBD-N9900SH Service Manual online
HBD-N7100W/N7100WL/N8100W/N9100W/N9100WL/N9150W/N9150WL/N9900SH
10
CHECKING METHOD OF NETWORK OPERATION
It is necessary to check the network operation, when replacing the
complete MB1004 board or WLAN/BT COMBO card (WBC1).
Check the operation of wireless and wired LAN, according to the
following method.
It is necessary to check the network operation, when replacing the
complete MB1004 board or WLAN/BT COMBO card (WBC1).
Check the operation of wireless and wired LAN, according to the
following method.
1. Checking Method of Wireless LAN Operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP).
Wireless access point with router function (AP).
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press the [m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
4. Select “Internet Settings”, and press the [ ] button on the re-
mote commander.
5. Press the [m]/[M] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [ ] button on the
remote commander.
remote commander.
6. The system starts searching for access points, and displays a
list of up available network name (SSID).
7. Check that access point (SSID) is displayed on the searching
result.
8. Press the [
?/1
] button to turn the power off.
Note:
Refer to the instruction manual about details of the setting method.
2. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [
?/1
] button to turn the power on.
3. Press the [HOME] button on the remote commander to enter
the home menu.
4. Press the [m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
5. Select “Internet Settings”, and press the [ ] button on the re-
mote commander.
6. Press the [m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [ ] button on the remote com-
mander.
mander.
7. Press the [m]/[M] buttons on the remote commander to select
“Auto”, and press the [ ] button on the remote commander.
8. Press the [,] button on the remote commander.
9. Press the [m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [ ] button on the remote
commander.
commander.
10. When “Internet Settings is now complete.” appears, then press
the [ ] button on the remote commander.
11. Press the [m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [ ] button
on the remote commander.
on the remote commander.
12. Press the [m]/[M] buttons on the remote commander to select
“IPv4”, and press the [ ] button on the remote commander.
13. Press the [<]/[,] buttons on the remote commander to
select “Start”, and press the [ ] button on the remote com-
mander.
mander.
14. Confi rm that “Network connections are correct” is displayed.
(When having confi rmed that “Network connections are cor-
rect” is displayed, advance to the step 20)
rect” is displayed, advance to the step 20)
15. Press the [ ] button on the remote commander.
16. Press the [m]/[M] buttons on the remote commander to select
16. Press the [m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [ ] button
on the remote commander.
on the remote commander.
17. Press the [m]/[M] buttons on the remote commander to select
“IPv6”, and press the [ ] button on the remote commander.
18. Press the [<]/[,] buttons on the remote commander to
select “Start”, and press the [ ] button on the remote com-
mander.
mander.
19. Confi rm that “Network connections are correct” is displayed.
20. Press the [
20. Press the [
?/1
] button to turn the power off.
Note:
Refer to the instruction manual about details of the setting method.
INSTALLATION METHOD OF THE WIRELESS SOUND
SYSTEM
SYSTEM
Note:
EZW-RT20
: Wireless transceiver for Chinese model
EZW-RT50
: Wireless transceiver for except Chinese model
TA-SA300WR : Surround amplifi er for HBD-N7100W/N8100W/N9100W/
N9150W
TA-SA400WR : Surround amplifi er for HBD-N7100WL/N9100WL/N9150WL/
N9900SH
Procedure:
1. Insert the wireless transceiver (EZW-RT50 or EZW-RT20) of
1. Insert the wireless transceiver (EZW-RT50 or EZW-RT20) of
the attachment in the wireless transceiver slot in the back of
the main unit and the surround amplifi er (TA-SA300WR or
TA-SA400WR).
the main unit and the surround amplifi er (TA-SA300WR or
TA-SA400WR).
Wireless transceiver
(EZW-RT50 or EZW-RT20)
(EZW-RT50 or EZW-RT20)
Wireless transceiver
(EZW-RT50 or EZW-RT20)
(EZW-RT50 or EZW-RT20)
Rear panel of the surround amplifier
(TA-SA300WR or TA-SA400WR)
(TA-SA300WR or TA-SA400WR)
Rear panel of the main unit
2. Connect the AC power cord of the main unit.
3. Press the [
3. Press the [
\/1
] button on the main unit to turn the power on.
4. Connect the AC power cord of the surround amplifi er (TA-
SA300WR or TA-SA400WR).
5. When wireless transmission is activated, the [LINK/STAND-
BY] indicator of the surround amplifi er (TA-SA300WR or TA-
SA400WR) turns green.
SA400WR) turns green.
Note:
Refer to the operating instructions when the [LINK/STAND-
BY] indicator of the surround amplifi er (TA-SA300WR or TA-
SA400WR) doesn’t light.
SA400WR) doesn’t light.
LINK/STANDBY indicator
– Front view –
Ver. 1.1
Click on the first or last page to see other HBD-N7100W / HBD-N7100WL / HBD-N8100W / HBD-N9100W / HBD-N9100WL / HBD-N9150W / HBD-N9150WL / HBD-N9900SH service manuals if exist.