Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N ADJUSTMENTS AND SETTINGS 4 – 60
5)
Set the patch image (adjustment pattern) printed in procedure
4) on the document table.
4) on the document table.
Set the patch image so that the thin line is on the left side as
shown in the figure.
shown in the figure.
At that time, place 5 sheets of white paper on the above patch
image (adjustment pattern).
image (adjustment pattern).
6)
Press [EXECUTE] key, and the printer gray balance adjust-
ment is executed automatically.
ment is executed automatically.
The message, "Will you go on to the copy gray balance adjust-
ment?" is displayed.
ment?" is displayed.
To execute the copy gray balance adjustment successively,
perform the procedures same as the above.
perform the procedures same as the above.
ADJ 12
Image send, FAX send mode
image quality adjustment
image quality adjustment
12-A
Color image send mode, image density and
gradation adjustment (by each mode)
gradation adjustment (by each mode)
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
Enter the Sim. 46-4 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
increased. When the adjustment value is decreased, the
image density is decreased.
4)
Scan the color document in the color scan mode (Scan to PC
or Scan to e-Mail), and check the density of the received
image.
or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure. The scanned image, however, is in monochrome.
procedure. The scanned image, however, is in monochrome.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
obtained.
12-B
Monochrome image send mode, image
density and gradation adjustment
(by each mode)
density and gradation adjustment
(by each mode)
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
Enter the Sim. 46-5 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
increased. When the adjustment value is decreased, the
image density is decreased.
4)
Scan a monochrome document in the color scan mode (Scan
to PC or Scan to e-Mail), and check the density of the received
image.
to PC or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure.
procedure.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
obtained.
Item/
Mode
Mode
Display
Document
mode
Setting
rage
Default
value
A
LOW
AUTO
Auto
1 - 99
50
B
TEXT
Text
1 - 99
50
C
TEXT/
PRINTEDPHOTO
Text/Printed
Photo
1 - 99
50
D
TEXT/PHOTO
Text/
Photograph
1 - 99
50
E
PRINTED PHOTO
Printed photo
1 - 99
50
F
PHOTOGRAPH
Photograph
1 - 99
50
G
MAP
Map
1 - 99
50
H
RIP
-
1 - 99
50
A
HIGH
AUTO
Auto
1 - 99
50
B
TEXT
Text
1 - 99
50
C
TEXT/PRINTED
PHOTO
Text/Printed
Photo
1 - 99
50
D
TEXT/PHOTO
Text/
Photograph
1 - 99
50
E
PRINTED PHOTO
Printed photo
1 - 99
50
F
PHOTOGRAPH
Photograph
1 - 99
50
G
MAP
Map
1 - 99
50
H
RIP
-
1 - 99
50
Thin line
Item/
Mode
Mode
Display
Document
mode
Setting
rage
Default
value
A
LOW
AUTOTEXT
Auto/Text
1 - 99
50
B
TEXT
Text
1 - 99
50
C
TEXT/PRINTED
PHOTO
Text/Printed
Photo
1 - 99
50
D
TEXT/PHOTO
Text/
Photograph
1 - 99
50
E
PRINTED PHOTO
Printed photo
1 - 99
50
F
PHOTOGRAPH
Photograph
1 - 99
50
G
MAP
Map
1 - 99
50
H
RIP
-
1 - 99
50
A
HIGH
AUTOTEXT
Auto/Text
1 - 99
50
B
TEXT
Text
1 - 99
50
C
TEXT/PRINTED
PHOTO
Text/Printed
Photo
1 - 99
50
D
TEXT/PHOTO
Text/
Photograph
1 - 99
50
E
PRINTED PHOTO
Printed photo
1 - 99
50
F
PHOTOGRAPH
Photograph
1 - 99
50
G
MAP
Map
1 - 99
50
H
RIP
-
1 - 99
50
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.