Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N ADJUSTMENTS AND SETTINGS 4 – 58
11-F
Printer image quality adjustment
(Individual adjustment)
(Individual adjustment)
a. General
This adjustment is used to execute the fine adjustment in each
mode only when a satisfactory image quality is not obtained by the
basic adjustments ADJ 11E (1) and ADJ 11E (2) or there is a
request from the user. Normally there is no need to execute this
adjustment.
mode only when a satisfactory image quality is not obtained by the
basic adjustments ADJ 11E (1) and ADJ 11E (2) or there is a
request from the user. Normally there is no need to execute this
adjustment.
This must be well understood for execution of the adjustment.
11-F
(1)
Printer density adjustment
(Low density section density adjustment)
(No need to adjust normally)
Printer density adjustment
(Low density section density adjustment)
(No need to adjust normally)
This adjustment is used to adjust the image density in the low den-
sity area in the printer mode.
sity area in the printer mode.
Adjust to reproduction setting of the low density image.
This adjustment is required in the following cases.
* When it is required not to reproduce images in the low density
section, or to reproduce low-density images.
* When there is request from the user.
1)
Enter the SIM 67-36 mode.
2)
Enter the adjustment value and press the [OK] key.
In case of increase of the image density on low density part,
increase the adjustment value. For diluting the image density
on low density part, decrease the adjustment value.
increase the adjustment value. For diluting the image density
on low density part, decrease the adjustment value.
11-F
(2)
Printer high density image density
reproduction setting (Supporting the high
density section tone gap)
(No need to adjust normally)
Printer high density image density
reproduction setting (Supporting the high
density section tone gap)
(No need to adjust normally)
When a tone gap is generated in the high density section in the
printer mode, the setting is changed to lower the density in the high
density section.
printer mode, the setting is changed to lower the density in the high
density section.
This setting is normally not required, however, in the following
cases, a change of setting must be made.
cases, a change of setting must be made.
* When a tone gap occurs on part of high density.
* To lower the density in the high density section.
a. Adjustment procedure
1)
Enter the SIM 67-34 mode.
2)
Select the item A, B with the scroll key.
* If a tone gap occurs on part of high density, set 0 to item A and B
The density of high density part decreases. However, the tone
gap is better.
gap is better.
* In case of more increase of the density on high density part, set 1
to item A and B.
The tone gap may occur in high density part.
NOTE: If the setting values of item B is changed, density of the
high density part is changed.
When these values are changed, be sure to perform the
printer gray balance and density adjustment. (Automatic
adjustment)
printer gray balance and density adjustment. (Automatic
adjustment)
11-F
(3)
Printer gamma adjustment for each dither
(Automatic adjustment)
(No need to adjust normally)
Printer gamma adjustment for each dither
(Automatic adjustment)
(No need to adjust normally)
a. General
This adjustment is used to adjust the gray balance and the density
in the monochrome mode, the heavy paper mode, and the gloss
paper mode.
in the monochrome mode, the heavy paper mode, and the gloss
paper mode.
This simulation is used to improve image quality in these modes
and images.
and images.
b. Adjustment procedures
1)
Enter the SIM67-54 mode.
2)
Press [EXECUTE] key.
A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.
The patch image (adjustment pattern) is printed out.
The patch image (adjustment pattern) is printed out.
3)
Set the patch image (adjustment pattern) printed in the proce-
dure 2) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
dure 2) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
Display/Item
Content
Setting
range
Default
A
K
(0:ENABLE
1:DISABLE)
0
K engine maximum density
correction mode Enable
correction mode Enable
0 - 1
1
1
K engine maximum density
correction mode Disable
correction mode Disable
B
BLACK MAX
TARGET
Scanner target value for BLACK
maximum density correction
maximum density correction
0 - 999
500
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.