Read Sharp MX-FX11 (serv.man5) Service Manual online
MX-FX11 FAX SOFTWARE SWITCH 2 – 8
31
1
Reception
CSI sending
Setting to determine whether or not to send the CSI signal.
The CSI signal contains the transmission source number.
"0": Yes (send the CSI signal)
"1": No (do not send the CSI signal)
The CSI signal contains the transmission source number.
"0": Yes (send the CSI signal)
"1": No (do not send the CSI signal)
Setting
2
Transmission
Echo suppressor tone
setting No. 1
setting No. 1
Setting to determine whether or not to have the echo suppressor tone in the
high-speed modulation mode.
"0": With V33
"1": Without V33
high-speed modulation mode.
"0": With V33
"1": Without V33
Setting
3
Transmission
Echo suppressor tone
setting No. 2
setting No. 2
Setting to determine whether or not to have the echo suppressor tone in the
high-speed modulation mode.
"0": With V17
"1": Without V17
high-speed modulation mode.
"0": With V17
"1": Without V17
Communication/
Setting
Setting
4
Transmission
Echo suppressor tone
setting No. 3
setting No. 3
Setting to determine whether or not to have the echo suppressor tone in the
high-speed modulation mode.
"0": With V29
"1": Without V29
high-speed modulation mode.
"0": With V29
"1": Without V29
Setting
5
Transmission
Echo suppressor tone
setting No. 4
setting No. 4
Setting to determine whether or not to have the echo suppressor tone in the
high-speed modulation mode.
"0": With V27
"1": Without V27
high-speed modulation mode.
"0": With V27
"1": Without V27
Communication/
Setting
Setting
6, 7
Reception
Image capacity when
receiving
(Reflect in DIS, Do not
reflect in DTC.)
receiving
(Reflect in DIS, Do not
reflect in DTC.)
This sets the reception resolution capacity when FAX calls arrive (when
sending DIS).
Reflect in DIS, Do not reflect in DTC.
"00": Very fine
"01": Fine
"10": When small
"11": Ordinary lettering
sending DIS).
Reflect in DIS, Do not reflect in DTC.
"00": Very fine
"01": Fine
"10": When small
"11": Ordinary lettering
Setting
8
Not used
32
1, 2
Reception
Designation of
reception size
(indicating the width of
reception capacity)
reception size
(indicating the width of
reception capacity)
This sets this machine’s receivable document width that is notified to the other
party’s machine when receiving.
"00": By loaded cassette
"01": A4 width
"10": B4 (A4, B4) width
"11": A3 (A4, B4, A3) width
When using the loaded cassette, width is as follows depending on the
maximum cassette size.
A5/5.5x8.5R size: A4 width
B5 size: B4 width
A4/8.5x11 size: A3 width
8.5x13/8.5x14: A3 width
B4 size: B4 width
11x17: B4/A3 width (changeover by means of the FAX soft SW)
A3 size: A3 width
A3 width is adopted in cases where a tray capable of receiving and printing
facsimiles is not set and cases where all cassettes are open.
party’s machine when receiving.
"00": By loaded cassette
"01": A4 width
"10": B4 (A4, B4) width
"11": A3 (A4, B4, A3) width
When using the loaded cassette, width is as follows depending on the
maximum cassette size.
A5/5.5x8.5R size: A4 width
B5 size: B4 width
A4/8.5x11 size: A3 width
8.5x13/8.5x14: A3 width
B4 size: B4 width
11x17: B4/A3 width (changeover by means of the FAX soft SW)
A3 size: A3 width
A3 width is adopted in cases where a tray capable of receiving and printing
facsimiles is not set and cases where all cassettes are open.
Setting
3
Transmission
Training
Setting whether the training in high speed sending is set to long or short in
V.17.
"0": Short
"1": Long
V.17.
"0": Short
"1": Long
4
Reception
Reception gain
changeover when
receiving
changeover when
receiving
Setting to determine the FTT determination method when confirming TCF
reception.
"0": Judge the EQM value to determine if the received data is 0
"1": Only judge from the EQM value. Accordingly, TCF confirmation becomes
loose
reception.
"0": Judge the EQM value to determine if the received data is 0
"1": Only judge from the EQM value. Accordingly, TCF confirmation becomes
loose
Communication/
Setting
Setting
5
Reception
Time out time setting
after starting TCF
signal reception
after starting TCF
signal reception
The time for time out is set after starting TCF signal reception.
"0": 4 seconds
"1": 2 seconds
"0": 4 seconds
"1": 2 seconds
Setting
6
Communication
Time between DCS-
TCF
TCF
Setting to determine how many seconds in the interval between DCS
transmission and sending of the TCF signal.
"0": 75msec
"1": 150msec
75±20ms in the ITU-T standard.
transmission and sending of the TCF signal.
"0": 75msec
"1": 150msec
75±20ms in the ITU-T standard.
Adjustment value
7, 8
Communication
300bps preamble send
time
time
The preamble send time is set in the FSK signal sending.
"00": 0.5 seconds
"01": 1 second
"10": 1.5 seconds
"11": 2 seconds
"00": 0.5 seconds
"01": 1 second
"10": 1.5 seconds
"11": 2 seconds
SW
No.
No.
Bit
No.
Item
SW selection and function
System settings
Click on the first or last page to see other MX-FX11 (serv.man5) service manuals if exist.