Read Sharp MX-FX11 (serv.man5) Service Manual online
MX-FX11 FAX SOFTWARE SWITCH 2 – 6
27
1, 2
Reception
CED signal sending
time
time
This sets the time over which the CED signal is sent.
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": No
"00": 3 seconds
"01": 4 seconds
"10": 5 seconds
"11": No
Communication/
Adjustment value
Adjustment value
3
Reception
CED/ANSam detection
time
time
This sets the time up until determination of the signal when detecting CED/
ANSam signals.
"0": 500ms
"1": 1000ms
ANSam signals.
"0": 500ms
"1": 1000ms
Adjustment value
4
Reception
V.34 mode function (on
call arrival)
call arrival)
Setting to determine whether or not to make the V.34 mode valid as machine
capacity when receiving (on call arrival).
"0": V.34 valid
"1": V.34 invalid
capacity when receiving (on call arrival).
"0": V.34 valid
"1": V.34 invalid
Setting
5
Transmission
V.34 mode function
(including polling when
calling)
(including polling when
calling)
Setting to determine whether or not to make the V.34 mode valid as machine
capacity when transmitting (calling and polling).
"0": V.34 valid
"1": V.34 invalid
capacity when transmitting (calling and polling).
"0": V.34 valid
"1": V.34 invalid
Setting
6
Transmission
V.34 mode function at
times of manual
communication
times of manual
communication
Setting to determine whether or not to make the V.34 mode valid at times of
manual communication (transmitting and receiving).
"0": V.34 valid
"1": V.34 invalid
However, in cases where the V.34 mode function (including polling when
calling) is set at 1: V.34 invalid, the V.34 mode will be rendered invalid even if
this SW is set to 0: valid.
manual communication (transmitting and receiving).
"0": V.34 valid
"1": V.34 invalid
However, in cases where the V.34 mode function (including polling when
calling) is set at 1: V.34 invalid, the V.34 mode will be rendered invalid even if
this SW is set to 0: valid.
Communication/
Setting
Setting
7
Transmission
3429 symbol rate
transmission enable
during V.34
transmission.
transmission enable
during V.34
transmission.
Setting to determine whether or not to enable 3429Hz as the symbol rate for
V.34.
When this is at "disable," 3429Hz is not selected.
However, only valid during transmission.
"0": disable
"1": enable
V.34.
When this is at "disable," 3429Hz is not selected.
However, only valid during transmission.
"0": disable
"1": enable
Setting
8
Transmission
Symbol rate 3200 high
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3200Hz is selected as the V.34 symbol rate, there are Low/High carriers,
but this setting determines whether or not both can be used.
When this is at "disable," 3200 High is not selected.
However, only valid during transmission.
When both Low/High are at "disable," SymbolRate=3200Hz is not selected.
"0": disable
"1": enable
but this setting determines whether or not both can be used.
When this is at "disable," 3200 High is not selected.
However, only valid during transmission.
When both Low/High are at "disable," SymbolRate=3200Hz is not selected.
"0": disable
"1": enable
Setting
28
1
Transmission
Symbol rate 3200 low
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3200Hz is selected as the V.34 symbol rate, there are Low/High carriers,
but this setting determines whether or not both can be used.
When this is at "disable," 3200 Low is not selected.
However, only valid during transmission.
"0": disable
"1": enable
but this setting determines whether or not both can be used.
When this is at "disable," 3200 Low is not selected.
However, only valid during transmission.
"0": disable
"1": enable
Setting
2
Transmission
Symbol rate 3000 high
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3000Hz is selected as the V.34 symbol rate, there are Low/High carriers,
but this setting determines whether or not both can be used.
When this is at "disable," 3000 High is not selected.
However, only valid during transmission.
When both Low/High are at "disable," SymbolRate=3000Hz is not selected.
"0": disable
"1": enable
but this setting determines whether or not both can be used.
When this is at "disable," 3000 High is not selected.
However, only valid during transmission.
When both Low/High are at "disable," SymbolRate=3000Hz is not selected.
"0": disable
"1": enable
Setting
3
Transmission
Symbol rate 3000 low
carrier transmission
enable during V.34
transmission
carrier transmission
enable during V.34
transmission
When 3000Hz is selected as the V.34 symbol rate, there are Low/High carriers,
but this setting determines whether or not both can be used.
When this is at "disable," 3000 Low is not selected.
However, only valid during transmission.
"0": disable
"1": enable
but this setting determines whether or not both can be used.
When this is at "disable," 3000 Low is not selected.
However, only valid during transmission.
"0": disable
"1": enable
Setting
4
Transmission
Symbol rate 3429
enable during V.34
transmission
enable during V.34
transmission
Setting whether use of 3429Hz is enabled or not as the symbol rate in V.34
transmission.
When this is set to [Disable], 3429Hz cannot be selected.
"0": disable
"1": enable
transmission.
When this is set to [Disable], 3429Hz cannot be selected.
"0": disable
"1": enable
5
Transmission
Symbol rate 2800
enable during V.34
transmission
enable during V.34
transmission
Setting to determine whether or not to enable 2800Hz as the symbol rate for
V.34.
When this is at "disable," 2800Hz is not selected.
"0": disable
"1": enable
V.34.
When this is at "disable," 2800Hz is not selected.
"0": disable
"1": enable
Setting
6
Transmission
Symbol rate 2743
enable during V.34
transmission
enable during V.34
transmission
Setting to determine whether or not to enable 2743Hz as the symbol rate for
V.34.
When this is at "disable," 2743Hz is not selected.
"0": disable
"1": enable
V.34.
When this is at "disable," 2743Hz is not selected.
"0": disable
"1": enable
Setting
SW
No.
No.
Bit
No.
Item
SW selection and function
System settings
Click on the first or last page to see other MX-FX11 (serv.man5) service manuals if exist.