Read Sharp MX-FX10 Service Manual online
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-9
66
17
DTMF signal send
Used to select the signal send level from 0dB and the soft SW set values and specify a dial number to be
sent. The DTMF signal of the specified dial number is sent continuously until the interrupt command is made
by pressing RETURN key. When another dial number is specified during sending of the signal, the signal
send level is returned to the soft SW set value before execution of the mode after completion of the mode.
Used to select the signal send level from 0dB and the soft SW set values and specify a dial number to be
sent. The DTMF signal of the specified dial number is sent continuously until the interrupt command is made
by pressing RETURN key. When another dial number is specified during sending of the signal, the signal
send level is returned to the soft SW set value before execution of the mode after completion of the mode.
19
SRAM backup
Used to back up and restore the SRAM contents.
Used to back up and restore the SRAM contents.
21
FAX information print
Used to print the following FAX information.
Used to print the following FAX information.
Main
code
code
Sub
code
Contents
Remark
Sim66-17 DTMF SIG.
Sim66-17 DTMF SIG.
Sim66-17 DTMF SIG.
1:MAX
2:SOFT SW.
2:SOFT SW.
( 1-2 )
X
[OK] key
[OK] key
[BACK] key
INPUT DIAL #
X
X
EXEC
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[C] key
[C] key
: Input clear and stop
Numeric keys
: Item selection, dial number input
[OK] key
: Input value settlement and execution
[START] key
: Input value settlement and execution
[BACK] key
: Signal send stop
SENDING SIGNAL
X
PRESS BACK TO STOP
X
PRESS BACK TO STOP
EXEC
After selection
with numeric key
with numeric key
The numeric key
input enters
the third digit.
input enters
the third digit.
Completion of execution
(Highlighted during execution)
(Highlighted during execution)
SIM66-17 initial window
Sim66-19
BACK UP
Sim66-19
BACK UP
NO DATA
SRAM BACK UP
ARE YOU SURE?EXEC
Sim66-19
BACK UP
WRONG FAX VER.
Sim66-19
BACK UP
1:SRAM BACK UP
2:SRAM RESTORE
2:SRAM RESTORE
( 1-2 )
X
Sim66-19
BACK UP
SRAM BACK UP
FINISHED
FINISHED
Sim66-19
BACK UP
SRAM BACK UP
PRESS BACK TO STOP
PRESS BACK TO STOP
SENDING
EXEC
[OK] key
[OK] key
[OK] key
[OK] key
[BACK] key
After inputting
1 or 2
1 or 2
After pressing
[OK] key,
during execution
[OK] key,
during execution
Completion of execution
(Highlighted during execution)
(Highlighted during execution)
After pressing [OK] key, during execution
After pressing [OK] key, during execution
SIM66-19 initial window
[BACK] key
SIM66-19 initial window
[BACK] key
SIM66-19 initial window
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
Numeric key
Numeric key
: Item selection
[OK] key
: Execution\
[START] key : Settlement of the input value
[BACK] key
[BACK] key
: Returns to the selection window.
[C] key
: Disable
Sim66-21 LIST
Sim66-21 LIST
Sim66-21 LIST
1:USER SW. LIST
2:SOFT SW. LIST
3:SYSTEM ERROR
(1 - 5)
2:SOFT SW. LIST
3:SYSTEM ERROR
(1 - 5)
X
SOFT SW. LIST
EXEC
PRINT STORED
Sim66-21 LIST
4:PROTOCOL MONITOR
5:FAX SIMULATION
5:FAX SIMULATION
(1 - 5)
X
[OK] key
[OK] key
[OK] key
Sim66-21 LIST
CAN NOT PRINT
Printer Error
After selection with numeric keys
After selection
with numeric
keys
with numeric
keys
After pressing
[OK] key,
during
execution
[OK] key,
during
execution
1sec later
SIM66-21 window
1sec later
SIM66-21 window
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
Numeric key
Numeric key
: Item selection
[OK] key
: Settlement and execution
[START] key
: Input value settlement and executio
[BACK] key
: Returns to the selection window.
keys
: Page switch
[C] key
: Disable
Click on the first or last page to see other MX-FX10 service manuals if exist.