Read Sharp MX-FX10 Service Manual online
MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-8
66
10
Image memory contents clear
Used to clear all the image data (including confidential receive contents) in the image memory of the FAX
section. The management table is also cleared (initialized) at the same time.
Used to clear all the image data (including confidential receive contents) in the image memory of the FAX
section. The management table is also cleared (initialized) at the same time.
11
300bps signal send
Used to send the specified signal at the speed of 300bps by setting the signal number. (Signal send is
continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from
0db and soft switch set values. The signal send level is returned to the sot SW set value before execution of
the mode after completion of the mode.
Used to send the specified signal at the speed of 300bps by setting the signal number. (Signal send is
continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from
0db and soft switch set values. The signal send level is returned to the sot SW set value before execution of
the mode after completion of the mode.
13
Dial test
Used to send the dial pulse and the DTMF signal, and perform the dial pulse make time adjustment and the
DTMF signal send level adjustment according to necessity.
Used to send the dial pulse and the DTMF signal, and perform the dial pulse make time adjustment and the
DTMF signal send level adjustment according to necessity.
Main
code
code
Sub
code
Contents
Remark
Sim66-10 IMAGE CLR
[OK] key
Sim66-10 IMAGE CLR
Sim66-10 IMAGE CLR
CLEAR IMAGE MEMORY
ARE YOU SURE? EXEC
CLEAR IMAGE MEMORY
EXEC
CLEARED IMAGE MEM.
DO POWER OFF
DO POWER OFF
Sim66-10 IMAGE CLR
CLEARED
Power source OFF/ON
Simulation code input window
Completion
of execution
(Highlighted
during execution)
of execution
(Highlighted
during execution)
Completion of execution
(Highlighted during execution)
(Highlighted during execution)
After pressing
[OK] key,
during execution
[OK] key,
during execution
With prints
Without prints
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input
window
[OK] key
: Settlement
[BACK] key
: Simulation code input window
[START] key
: Settlement
[C] key
: Disable
[BACK] key
Sim66-11 300bps SIG.
Sim66-11 300bps SIG.
[OK] key
Sim66-11 300bps SIG.
Sim66-11 300bps SIG.
SIGNAL LEVEL
1:MAX
2:SOFT SW.
( 1 - 2 )
1:MAX
2:SOFT SW.
( 1 - 2 )
X
1:NO SIG.
4:00000
2:11111
5:010101
3:11110
6:00001
( 1 - 6 )
X
NO SIGNAL
EXEC
SIM66-11 initial window
OUTPUTING SIGNAL
PRESS BACK TO STOP
PRESS BACK TO STOP
EXEC
After selection with numeric keys
[OK] key
[OK] key
After selection
with numeric keys
with numeric keys
After pressing [OK] key,
during execution
during execution
[BACK] key
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[C] key
[C] key
: Input clear
keys
: Page switch
Numeric keys
: Item selection
[OK] key
: Input value settlement and execution
[START] key
: Input value settlement
[BACK] key
: Signal send stop
Sim66-13 DIAL TEST
1:PULSE 10pps
2:PULSE 20pps
3:DTMF
( 1-3 )
2:PULSE 20pps
3:DTMF
( 1-3 )
X
SIM66-13 initial window
SIM66-13 initial window
Select with numeric key
and press [OK] key.
and press [OK] key.
Select with numeric keys
and press [OK] key.
and press [OK] key.
SENDING 10 pps Yyms
INPUT DIAL #
XXXXXXXXXXXX
INPUT DIAL #
XXXXXXXXXXXX
EXEC
[OK] key
[OK] key
Sim66-13 DIAL TEST
PULSE 10pps
INPUT MAKE TIME
INPUT MAKE TIME
YY
( 26-41 )
YY
Sim66-13 DIAL TEST
PULSE 10pps
Yyms
INPUT DIAL #
XXXXXXXXXXXXX
XXXXXXXXXXXXX
EXEC
Sim66-13 DIAL TEST
SEND 10 pps
Yyms
INPUT DIAL #
XXXXXXXXXXXXX
XXXXXXXXXXXXX
EXEC
Sim66-13 DIAL TEST
Sim66-13 DIAL TEST
INPUT HIGH LEVEL
DTMF SOFT SW.
DTMF SOFT SW.
Y
( 0-21 )
XX
Sim66-13 DIAL TEST
SELECT HIGH LEVEL
1:DEFAULT
2:SOFT SW.
1:DEFAULT
2:SOFT SW.
Y
( 1-2 )
X
Sim66-13 DIAL TEST
INPUT LOW LEVEL
DTMF SOFT SW.
DTMF SOFT SW.
Y
( 0-15 )
XX
Sim66-13 DIAL TEST
DTMF HIGH:XX LOW:YY
INPUT DIAL #
XXXXXXXXXXXXX
INPUT DIAL #
XXXXXXXXXXXXX
EXEC
Sim66-13 DIAL TEST
DTMF HIGH:XX LOW:YY
INPUT DIAL #
XXXXXXXXXXXXX
INPUT DIAL #
XXXXXXXXXXXXX
EXEC
Sim66-13 DIAL TEST
SELECT LOW LEVEL
1:DEFAULT
2:SOFT SW.
1:DEFAULT
2:SOFT SW.
Y
( 1-2 )
X
After selection
with numeric key
with numeric key
[OK] key
[OK] key
After selection with numeric key
[OK] key
[OK] key
[OK] key
[OK] key
[OK] key
After selection
with numeric
key
with numeric
key
After selection
with numeric
key
with numeric
key
[OK] key
The input of
numeric key
enters the
fourth digit.
(If there are too
many, scroll to the left.)
numeric key
enters the
fourth digit.
(If there are too
many, scroll to the left.)
After pressing [OK] key, during execution
After pressing
[OK] key,
during
execution
[OK] key,
during
execution
Completion of execution
(Highlighted during execution)
(Highlighted during execution)
Completion of execution
(Highlighted during execution)
(Highlighted during execution)
[CA] key
: Simulation cancel
[INTERRUPT] key: Sub code input window
[C] key
[C] key
: Input clear
Numeric key
: Input of time and dial number
and selection of an item
[OK] key
: Settlement and execution of an input
[START] key
: Settlement of an input
[BACK] key
: Returns to the selection window
XXXXXXXX
: Input dial
When "1" is selected
When "2" is selected
Click on the first or last page to see other MX-FX10 service manuals if exist.