MX-FX10. Service Manual. - Sharp Copying Equipment Service Manual (repair manual). Page 17

MX-FX10 SIMULATIONS, FAX SOFTWARE SWITCH 4-7

66

4

Signal send mode
Used to send signals to the line and the machine speaker by setting the signal number. (Signal send is 
continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from 
0db and the soft SW values. Since the level setting is not required for 01 and 31 - 35, the selection menu 
does not appear. The signal send level is returned to the soft SW set value before execution of the mode 
when completing the mode.

6

Print pass code print
Used to print the confidential ID table (confidential box number, confidential box name, confidential pass 
code). Sharp mode confidential information is printed separately.

7

Image memory content print
Used to print all the image data (confidential receive contents, remote send images, and images which are 
not sent yet) in the image memory of the FAX section. The printed images are remained in the memory after 
printing.

Main 
code

Sub 

code

Contents

Remark

Sim66-4 SIGNAL OUT

Sim66-4 SIGNAL OUT

Sim66-4 SIGNAL OUT

Sim66-4 SIGNAL OUT

Sim66-4 SIGNAL OUT

SIGNAL SELECT

(1 - 35)

1:NO SIGNAL
2:33600bps(V34)
3:31200bps(V34)
(1 - 35)

XX

After selection with numeric keys

[OK] key

[OK] key

[OK] key

[BACK] key

33600bps(V34)
1:MAX
2:SOFT SW.
(1 - 2)

X

33600bps(V34)
0dB

EXEC

33600bps(V34)
PRESS BACK TO STOP

EXEC

Sim66-4 SIGNAL OUT

34:DP MAKE
35:DP BREAK

(1 - 35)

XX

After pressing 
[OK] key

SIM66-4 initial window

[CA] key

: Simulation cancel

[INTERRUPT] key: Sub code input window
[C] key

: Input clear

          key

: Page select

Numeric keys

: Number input and item selection

[OK] key

: Input value settlement and execution

[START] key

: Input value settlement

[BACK] key

: Signal send stop

The window is switched with the up and down keys.
Input and switching the window are irrelevant.
Not highlighted with an input of a value.
The window is not switched, either.

When "1: NO SIGNAL" or "31: PSEUDO RNG" - "33: R.B. TONE NONE"
is selected, "0dB" and "SOFT SW" are not selected.
When one of these is selected, the second line is the signal name,
the third and fourth lines are empty, and the fifth line is EXEC display. 

1sec later

Sim66-6

PASS CODE

Sim66-6

PASS CODE

Sim66-6

PASS CODE

PRINT STORED

[OK] key

[OK] key

[OK] key

PRINT CONF.

               EXEC

NO DATA

Sim66-6

PASS CODE

CAN NOT PRINT

1sec later

1sec later

1sec later

[CA] key

: Simulation cancel

[INTERRUPT] key : Sub code input

window

[OK] key

: Settlement

[START] key

: Settlement

[C] key

: Disable

[BACK] key

: Disable

Sim66-7 PRINT MEMORY

Sim66-7 PRINT MEMORY

Sim66-7 PRINT MEMORY

PRINT STORED

PRINT IMAGE MEMORY

               EXEC

NO DATA

Sim66-7 PRINT MEMORY

CAN NOT PRINT

(When there is no image memory)

[OK] key

[OK] key

[OK] key

1sec later

1sec later

1sec later

[CA] key

: Simulation cancel

[INTERRUPT] key : Sub code input

window

[OK] key

: Settlement

[START] key

: Settlement

[C] key

: Disable

[BACK] key

: Disable