Read Sharp MX-FX10 (serv.man3) User Guide / Operation Manual online
104
SYSTEM SETTINGS
#OF RINGS AT. RX
When the reception mode is set to auto, this setting is
used to select the number of rings on which the
machine automatically receives a call and begins fax
reception. (See "RECEIVING A FAX" on page 28.)
Any number of rings from 0 to 9* can be selected.
Normally "2" is selected.
* In Singapore, India and Taiwan, it can be set to any
used to select the number of rings on which the
machine automatically receives a call and begins fax
reception. (See "RECEIVING A FAX" on page 28.)
Any number of rings from 0 to 9* can be selected.
Normally "2" is selected.
* In Singapore, India and Taiwan, it can be set to any
number from 0 to15.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
PROCEDURE" (page 94).
2
Select "RCV. FUNCTION" with the [
] or
[
] key and then press the [OK] key.
3
Select "#OF RINGS AT. RX" with the [
] or
[
] key and then press the [OK] key.
4
Enter the number of rings (0 to 9) with the
numeric keys and then press the [OK] key.
numeric keys and then press the [OK] key.
The number of rings can be set to any number from 0 to 9.
TRAY SELECTION
This setting is used to select which output trays can be
used for received faxes. All output trays are initially
enabled.
used for received faxes. All output trays are initially
enabled.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
PROCEDURE" (page 94).
2
Select "RCV. FUNCTION" with the [
] or
[
] key and then press the [OK] key.
3
Select "TRAY SELECTION" with the [
] or
[
] key and then press the [OK] key.
4
Select the tray that you wish to enable with the
[
[
] or [
] key and then press the [OK] key.
• The selected tray is enabled and a checkmark
appears in the checkbox.
• If this procedure is performed when the tray is enabled,
the checkmark will be cleared and the tray disabled.
5
To enable another tray, repeat step 4. To
exit, press the [BACK] key.
exit, press the [BACK] key.
RECEIVED DATA PRINT CONDITION
This setting determines the selection condition for paper
when printing received documents. Select one of the three
conditions below. "REDUCTION" is normally selected.
when printing received documents. Select one of the three
conditions below. "REDUCTION" is normally selected.
• "REDUCTION"
Each received image is printed at actual size when
possible. When not possible, the image is
automatically reduced before printing.
possible. When not possible, the image is
automatically reduced before printing.
• "DIVISION"
Each received image is printed at actual size. If necessary,
the image is split onto multiple sheets of paper.
the image is split onto multiple sheets of paper.
• "ACTUAL SIZE"
The received fax image is printed at its actual size
(without dividing it onto multiple sheets of paper). If
the same size of paper or larger paper is not loaded,
the fax will be received in memory and will not be
printed until a suitable size of paper is loaded.
(without dividing it onto multiple sheets of paper). If
the same size of paper or larger paper is not loaded,
the fax will be received in memory and will not be
printed until a suitable size of paper is loaded.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
PROCEDURE" (page 94).
2
Select "RCV. FUNCTION" with the [
] or
[
] key and then press the [OK] key.
3
Select "RECEIVED DATA PRINT
CONDITION" with the [
CONDITION" with the [
] or [
] key and
then press the [OK] key.
4
Select "REDUCTION", "DIVISION" or
"ACTUAL SIZE" with the [
"ACTUAL SIZE" with the [
] or [
] key
and then press the [OK] key.
AUTO RCV REDUCE TO REGULAR SIZE
When you receive a fax that includes the sender's
name and number, the received image is slightly larger
than the standard size*. This setting lets you select
whether or not the received image is automatically
reduced before printing to fit the standard size.
Normally this setting is enabled.
* Standard sizes are sizes such as A4 and B5.
name and number, the received image is slightly larger
than the standard size*. This setting lets you select
whether or not the received image is automatically
reduced before printing to fit the standard size.
Normally this setting is enabled.
* Standard sizes are sizes such as A4 and B5.
1
Follow steps 1 through 6 of "INITIAL
PROCEDURE" (page 94).
PROCEDURE" (page 94).
2
Select "RCV. FUNCTION" with the [
] or
[
] key and then press the [OK] key.
3
Select "AUTO RCV REDUCE TO REGULAR
SIZE" with the [
SIZE" with the [
] or [
] key and then
press the [OK] key.
• The setting is enabled and a checkmark appears in
the checkbox.
• If this procedure is performed when the setting is
enabled, the checkmark will be cleared and the
setting disabled.
setting disabled.
If the number of rings is set to 0, the
machine will receive faxes without ringing.
machine will receive faxes without ringing.
• The trays that can be enabled will vary
depending on the options that are installed.
• The trays cannot all be disabled.
Note
Note
• If this setting is disabled (no reduction)
and the received data print condition is set
to division, the image may be clipped.
to division, the image may be clipped.
• If auto receive reduce is disabled, an image
larger than the standard size will be cut off.
However, the image will be clearer because it
will be printed at the same size as the original.
However, the image will be clearer because it
will be printed at the same size as the original.
Note
Pegasus-E_Fax_Ex.book 104 ページ 2009年6月5日 金曜日 午後1時49分
Click on the first or last page to see other MX-FX10 (serv.man3) service manuals if exist.