Read Sharp AR-M550 (serv.man15) Service Manual online
AR-M550/M620 SIMULATION 8 - 73
4) Press [START] key.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.
is pressed, the adjustment value is set and copying is per-
formed.
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the scan mode to be adjusted
with 10-key. (Select one of 3 - 5.)
2) Press [START] key.
(Scan off-center position adjustment)
1) Enter the scan image position adjustment value with 10-key.
2) Press [P] key or [START] key.
When [START] key is pressed, the adjustment value is set and
copying is performed.
copying is performed.
Check the off-center of the printed image.
Repeat the above procedures until a satisfactory result is obtained.
(UNIT: 0.1mm/step When the adjustment value is increased, the print
image is shifted to the front direction.)
image is shifted to the front direction.)
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Select one of 1 - 6)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.
changed to the duplex print mode.
∗
To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.
is pressed, the adjustment value is set and copying is per-
formed.
Set range
25 - 400 (%)
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
50-12
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)
(Adjusted separately for each scan mode.)
Section
Item
Picture quality
Image position
Item
Set range
Default
0 TRAY SELECT
Paper feed tray
selection
selection
1 - 5
–
1 COPY START
Copy START (Default)
–
–
2 MAGNIFICATION Print magnification ratio
25 - 400%
100
(Resist adjustment value)
3 PLATEN
OC mode adjustment
0 - 99
50
4 SPF SIDE1
SPF front surface
adjustment
adjustment
5 SPF SIDE2
SPF back surface
adjustment
adjustment
50
2
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 2, and
press [START] key.
press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)
3.TRAY1
50
4.TRAY2
50
5.TRAY3
50
6.TRAY4
50
7.BPT
50
8.LCC
50
9. ADU
50
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
2.TRAY1
1
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Set range
25 - 400 (%)
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.