Read Sharp AR-M550 (serv.man15) Service Manual online
AR-M550/M620 SIMULATION 8 - 72
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
changed to the duplex mode (DD), and a duplex copy is made.
Operation/Procedure
(Print image off-center position adjustment)
NOTE: This simulation cannot provide an accurate adjustment. Do not
use.
1) Enter the number corresponding to the number of the paper feed
tray to be adjusted with 10-key. (Select one of 3 - 9.)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed, the
adjustment value set and copying is performed.
(Image off-center adjustment)
1) Enter 1 with 10-key.
2) Press [START] key. The adjustment pattern is printed.
3) Check the off-center of the printed image.
(UNIT: 0.1mm/step When the adjustment value is increased, the
print image is shifted to the front direction.)
print image is shifted to the front direction.)
NOTE: This adjustment can be performed with SIM 50-5.
(Copy condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Select one of 1 - 6)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.
changed to the duplex print mode.
∗
To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
(Image loss set value: SIDE 2)
8
LEAD_EDGE
Back surface lead edge
image loss set value
image loss set value
0 - 99
15
9
FRONT/REAR
Back surface side edge
image loss set value
image loss set value
20
10 TRAIL_EDGE
Back surface rear edge
image loss set value
image loss set value
0 - 20
0
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
50
1
2
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
200
(ADJUSTMENT DATA) 3.L4
160
4.L5
160
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE
15
6.FRONT/REAR
20
7.TRAIL_EDGE
0
SIDE2: 8.LEAD_EDGE
15
9.FRONT/REAR
20
10.TRAIL_EDGE
0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
PRESS START.
3.L4
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
50-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the print image off-center position.
(Adjusted separately for each paper feed section.)
(Adjusted separately for each paper feed section.)
Section
Item
Picture quality
Image position
Item
Set range Default
0 TRAY SELECT
Paper feed tray selection
1 - 6
–
1 COPY START
Copy START (Default)
–
–
2 MAGNIFICATION Print magnification ratio
25 - 400%
100
(Off-center adjustment value)
3 TRAY1
Tray 1 adjustment
0 - 99
50
4 TRAY2
Tray 2 adjustment
5 TRAY3
Tray 3 adjustment
6 TRAY4
Tray 4 adjustment
7 BPT
Manual feed tray
adjustment
adjustment
8 LCC
Side LCC adjustment
9 ADU
Adjustment when paper is
fed again from ADU
fed again from ADU
Normal display
NOW COPYING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.