Read Sharp AR-M550 (serv.man15) Service Manual online
AR-M550/M620 SIMULATION 8 - 69
3) If the adjustment result is not satisfactory, perform the following
procedures.
∗
If the lead edge void area is not 3.5mm:
Change the adjustment value of RRCB and perform the adjust-
ment. (Change the adjustment value of RRCB and press
[START] key.)
(Shift for the adjustment value change: 0.1mm/step)
Change the adjustment value of RRCB and perform the adjust-
ment. (Change the adjustment value of RRCB and press
[START] key.)
(Shift for the adjustment value change: 0.1mm/step)
(Front/rear frame direction void area adjustment)
Adjust so that the total of the front/rear direction void areas is 7.0mm.
(Change the adjustment values of FRONT/REAR, and press [START]
key.)
(Change the adjustment values of FRONT/REAR, and press [START]
key.)
Front frame void area = 3.5mm
Rear frame void area = 3.5mm
(Paper resist adjustment)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 3 - 9.) (Table 1)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed, the
adjustment value is set and printing is performed. (Table 2)
If the relative positions of paper and print images vary or a paper jam
occurs, change the adjustment value.
occurs, change the adjustment value.
(Print condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex print mode.
mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed instead, the adjustment value is set and copying is
performed.
is pressed instead, the adjustment value is set and copying is
performed.
(Table 1)
(Table 2)
(Table 3)
Item
Set
range
Default
0
TRAY SELECT Paper feed tray selection (1 - 6)
–
–
1
PRINT START
Print start (Default)
–
–
(Lead edge adjustment value)
2
RRCB
Resist roller clutch ON timing
adjustment value
adjustment value
0 - 99
50
(Resist adjustment value)
3
TRAY1
Tray 1 adjustment
0 - 99
50
4
TRAY2
Tray 2 adjustment
5
TRAY3
Tray 3 adjustment
6
TRAY4
Tray 4 adjustment
7
BPT
Manual feed tray adjustment
8
LCC
Side LCC adjustment
9
ADU
Adjustment when paper is fed
again from ADU
again from ADU
(Off-center set value) Self print
10 TRAY 1
Tray 1 adjustment
0 - 99
50
11 TRAY 2
Tray 2 adjustment
12 TRAY 3
Tray 3 adjustment
13 TRAY 4
Tray 4 adjustment
14 BPT
Manual feed tray adjustment
15 LCC
Side LCC adjustment
16 ADU
Adjustment when paper is fed
again from ADU
again from ADU
(Void set value)
17 LEAD_EDGE
(DENA)
Lead edge void set value
0 - 99
35
18 TRAIL_EDGE
(DENB)
Rear edge void adjustment
value
value
19 FRONT/REAR
Front/Rear void adjustment
value
value
20 SIDE2 ADJ.
RRCB correction value in the
back surface print mode
back surface print mode
1 - 99
50
Normal display
NOW PRINTING.
ERROR display
Door open
DOOR OPEN.
Jam
JAM
Paper empty
PAPER EMPTY.
1
TRAY1
TRAY1
2
TRAY2
TRAY2
3
TRAY3
TRAY3
4
TRAY4
TRAY4
5
BPT
Manual feed
6
LCC
Side LCC
Select 0, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
50
2
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. NOW PRINTING.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
2.RRCB
Select 1,
and press
[START] key.
and press
[START] key.
Select other than 0 - 1, and press [START] key.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB
LEAD EDGE: 2.RRCB
50
20.SIDE2 ADJ.
50
RESIST: 3.T1
50
4.T2
50
5.T3
50
6.T4
50
7.BPT
50
8.LCC
50
9.ADU
50
OFF CENTER: 10.T1
50
11.T2
50
12.T3
50
13.T4
50
14.BPT
50
15.LCC
50
16.ADU
50
(VOID SETTING) 17.LEAD_EDGE(DENA)
50
18.TRAIL_EDGE(DENB)
30
19.FRONT/REAR
30
1
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 1-16, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.