Read Sharp AR-M351U / AR-M451U (serv.man17) Service Manual online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 84
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-
key.
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of
an error, "NG" is displayed.
an error, "NG" is displayed.
When check is "repeat," the operation is continued until the result
is NG or [CUSTOM SETTINGS] key is pressed.
is NG or [CUSTOM SETTINGS] key is pressed.
Operation/Procedure
1) Enter the number corresponding to the destination.
2) Press [START] key.
Operation/Procedure
1) The confirmation window is displayed. Select whether rewrit-
ing of the program into PIC installed in the FAX VOX is per-
formed or not.
formed or not.
NOTE: Release the write protect notch.
FAX program writing enabled (Jumpers and DIP SW
depending on the model.)
depending on the model.)
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of
an error, "NG" is displayed.
an error, "NG" is displayed.
NG cause:
• Write protect is set.
• PIC is not installed.
• Access error to PIC
Press [START] key.
After completion of reloading
66-36
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check interface between MFPC controller
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
Section
FAX
Item
Operation
1
MFPC
←
MDMC
Date line once only
2
MFPC
→
MDMC
Date line once only
3
MFPC
←
MDMC
Data line repeat
4
MFPC
→
MDMC
Data line repeat
5
MFPC
←
MDMC
Command line once only
6
MFPC
→
MDMC
Command line once only
7
MFPC
←
MDMC
Command line repeat
8
MFPC
→
MDMC
Command line repeat
SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-35
MODEM PROGRAM RELOAD.
EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MDPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)
1
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...
Press [START] key.
When check is "once" or
"repeat" and the result is "NG":
"repeat" and the result is "NG":
When check is "repeat" and
[CUSTOM SETTINGS] key ON:
[CUSTOM SETTINGS] key ON:
66-39
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the destination specifications. (Only
when FAX is installed)
when FAX is installed)
Section
FAX
Item
Specifications Operation
66-42
Purpose
Setting
Function
(Purpose)
(Purpose)
PIC program rewriting (Only when FAX is
installed)
installed)
Section
FAX
Item
Operation
1
YES
Execution
2
NO
Cancel
Press [START] key.
SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1-6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A./CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA
1
SIMULATION 66-42
PIC PROGRAM RELOAD.
ARE YOU SURE ?
1.YES
2.NO
1
Press [START] key.
Press [START] key.
SIMULATION 66-42
PIC PROGRAM RELOAD EXECUTING ....
Press [CUSTOM SETTINGS] key.
SIMULATION 66-42
PIC PROGRAM RELOAD
OK
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.