Read Sharp AR-C260 (serv.man12) Service Manual online
AR-C260/C260M SIMULATION 9 - 15
During the load operation, the [EXECUTE] key and the load key are
highlighted. Under this state, pressing the [EXECUTE] key interrupts
the load operation.
highlighted. Under this state, pressing the [EXECUTE] key interrupts
the load operation.
(Loads to be selected)
(When the sorter is installed)
(Sensors to be detected)
3
-3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the loads in the finisher and the control
circuit.
circuit.
Section
Finisher
Item
Operation
Operation/
Procedure
Procedure
1. The names of the loads that can be checked are
displayed. Select a load to be checked with the key.
2. Press the [EXECUTE] key. The selected load
operates.
FFM
Transport motor
FFSM
Stapler motor
FPM
Paddle motor
FLM
Shift motor
FAM
Bundle exit motor
FPNM
Punch motor
FFJM
Alignment motor (F)
FPSM
Puncher side resist motor
FRJM
Alignment motor (R)
FFC
Folding clutch
FSM
Slide motor
SBSM
Bin unit shift motor
SPFM
Transport motor
SGBM
Guide bar drive motor
3
-10
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to adjust the sections in the finisher.
Section
Finisher
Item
Operation
Operation/
Procedure
Procedure
1. Select the adjustment item with the scroll key.
2. Enter the adjustment value with the 1o-key and press
2. Enter the adjustment value with the 1o-key and press
the OK key to set the value.
Item
Set
range
Initial
value
value
A
Saddle binding position adjustment
0 – 400
200
B
Saddle folding position adjustment
0 – 400
200
C
Front alignment position adjustment
0 – 20
10
D
Rear alignment position adjustment
0 – 20
10
E
Staple rear one-point binding position
adjustment
adjustment
0 – 200
100
F
Staple front one-point binding position
adjustment
adjustment
0 – 200
100
G
Staple two-point binding center adjustment
0 – 200
100
H
Staple two-point binding pitch adjustment
0 – 100
50
I
Punch center adjustment
47 – 53
50
J
Punch hole position adjustment
0 – 100
50
4
4
-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operations of the desk/large capacity
tray sensors and detectors and the related circuits.
tray sensors and detectors and the related circuits.
Section
Paper feed
Item
Operation
Operation/
Procedure
Procedure
The operating conditions of the sensors and detectors in
the paper feed section are displayed. The active sensors
and detectors are highlighted.
the paper feed section are displayed. The active sensors
and detectors are highlighted.
DLUD1
Desk 1cs upper limit detection
DLUD2
Desk 2cs upper limit detection
DLUD3
Desk 3cs upper limit detection
DPED1
Desk 1cs paper empty detector
DPED2
Desk 2cs paper empty detection
DPED3
Desk 3cs paper empty detection
DCSPS1
Desk 1cs remaining quantity detection
DCSPS2
Desk 2cs remaining quantity detection
DCSPS3
Desk 3cs remaining quantity detection
DPPD1
Desk paper transport detection 1
DPPD2
Desk paper transport detection 2
DPPD3
Desk paper transport detection 3
DLUID1
Desk 1cs lift unit installation detection
DLUID2
Desk 2cs lift unit installation detection
DLUID3
Desk 3cs lift unit installation detection
DDOPD
Desk door open detection
DCSS11
Desk 1cs paper size detection 1
DCSS12
Desk 1cs paper size detection 2
DCSS13
Desk 1cs paper size detection 3
DCSS14
Desk 1cs paper size detection 4
DCSS21
Desk 2cs paper size detection 1
DCSS22
Desk 2cs paper size detection 2
DCSS23
Desk 2cs paper size detection 3
DCSS24
Desk 2cs paper size detection 4
DCSS31
Desk 3cs paper size detection 1
DCSS32
Desk 3cs paper size detection 2
DCSS33
Desk 3cs paper size detection 3
DCSS34
Desk 3cs paper size detection 4
LRE
LCC remaining quantity detection
LUD
LCC upper limit detection
LDD
LCC lower limit detection
LPED
LCC paper empty detection
LPFD
LCC paper exit detection
LDSW
LCC door open detection
LTOD
LCC release detection
24V
LCC 24V detection
LCD
LCC cassette detection
Click on the first or last page to see other AR-C260 (serv.man12) service manuals if exist.