AR-C170 (serv.man26). Simulation - Sharp Copying Equipment Service Manual (repair manual). Page 17

Read Sharp AR-C170 (serv.man26) Service Manual online

AR-C170M  SIMULATION  9 - 17
2. When the [EXECUTE] key is pressed, the key is highlighted 
and the selected discharge lamp is lighted for 30sec. If the 
[EXECUTE] key is pressed while the lamp is lighted, the lamp 
is turned OFF.
(Loads to be selected)
When BLUM is ON, the belt moves up.
When BLUM is OFF, the belt moves down.
2. Press the [EXECUTE] key.
The selected load is operated. During operation, the 
[EXECUTE] key is highlighted. If the [EXECUTE] key is 
pressed while it is highlighted, the operation is stopped.
(Loads to be selected.)
The setup contents of this simulation remain unchanged until 
the power is turned off. When this simulation is executed, SIM 7-
8 (Warm-up time display setting) is canceled.
(Set content)
5
-4
Purpose
Operation test/check
Function 
(Purpose)
Used to check the operations of the discharge lamp 
and its control circuit.
/
Section
Process (Photoconductor, developing, 
transfer, cleaning)
Others
Item
Operation
Operation/
Procedure
1. Select the target discharge lamp with the [K], [C], 
[M], and [Y] keys. (K: Black, C: Cyan, 
M: Magenta, Y: Yellow)
6
6
-1
Purpose
Operation test/check
Function 
(Purpose)
Used to check the operations of the loads (clutches 
and solenoids) in the paper transport system, 
transfer, and fusing, and the control circuit.
Section
Paper transport (paper exit, switchback, transport), 
transfer, fusing
Item
Operation
Operation/
Procedure
1. The names of the loads that can be checked are 
displayed. Select the load to be checked with the 
key, and the selected load is highlighted.
2. Press the [EXECUTE] key. The selected load 
starts the operation. During the operation of the 
load, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed while it is highlighted, 
the operation is stopped.
CPFC
Cassette transport clutch
TRC
Cassette paper feed clutch
MTRC
Manual paper feed clutch
MPFC
Manual transport clutch
GSS
Paper exit gate select solenoid
RRM
Resist roller motor (PSM)
PFM
Paper feed motor (Vertical transport)
FUM
Fusing motor
BLUM
Lift motor
BLUM (R)
Lift motor (Reverse rotation/waste toner transport 
motor)
OSM
Offset motor (Job separator)
CARB
Calibration plate
6
-2
Purpose
Operation test/check
Function 
(Purpose)
Used to check the operations of the fan motors and 
the control circuits.
Section
Others
Item
Operation
Operation/
Procedure
1. The loads that can be checked are displayed. 
Select one to be checked.
VFM1
Fusing fan 1
VFM2
Fusing fan 2
PSFM
Power fan
PRTCFM
Process exhaust fan
SIROCCOFM
Sirocco fan
7
7
-1
Purpose
Setting/Operation test/check
Function 
(Purpose)
Used to set the aging conditions.
Item
Operation
Operation/
Procedure
1. Press each corresponding key to set for the 
aging operation.
(Set items of each key)
The selected key is highlighted.
2. Press the [EXECUTE] key.
Aging is set and the display returns to the 
simulation main code entry menu.
[AGING]
Jam detection setup
[INTERVAL]
Intermittent setup
[MISFEED DISABLE]
Jam detection YES/NO setup
[FUSING DISABLE]
Fusing operation YES/NO detection 
[WARMUP DISABLE]
Warm-up saving setup
[DV CHECK DISABLE] Developing tank detection YES/NO setup
[SHADING DISABLE]
Shading saving setup
[CCD GAIN FREE]
No setting of CCD gain adjustment
Page of 72
Display

Click on the first or last page to see other AR-C170 (serv.man26) service manuals if exist.