Read Sharp AR-405 Handy Guide online
TECHNICAL UPDATE
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
49
VERSION 1C
MARCH 2002
PERIPHERALS
Model
Fault
Advice
AR-FN1
Paper jams at FPID
Paper catches when using the short
path. Adjust the position of the short
patch gate solenoid. Make sure the
springs have been removed from the
exit door when installing a finisher (not
AR505.507).
path. Adjust the position of the short
patch gate solenoid. Make sure the
springs have been removed from the
exit door when installing a finisher (not
AR505.507).
AR-FN1/3
FPFD3 & FPFD4 jams when using
staple mode.
staple mode.
Incorrect pressure of transport rollers
on transport door. Relocate rollers
and check if roller shaft is binding with
the location guides.
on transport door. Relocate rollers
and check if roller shaft is binding with
the location guides.
AR-FN1/3
FT30D_N paper jams.
Damaged delivery gate 3 – replace
(0EUGID0426L// - PG10-20).
(0EUGID0426L// - PG10-20).
AR-FN1/3
FSTIDS paper jams
Actuator not fully engaging with the
detector. Remove actuator and add 1
turn to the return spring.
detector. Remove actuator and add 1
turn to the return spring.
AR-FN1/3
FPFD2 jam – unable to reset.
The top cover of the FN1/3 has been
bent causing the PFD2 sensor to foul
the ribs on the cover – replace.
bent causing the PFD2 sensor to foul
the ribs on the cover – replace.
AR-FN1/3
FPFRD3/4 misfeeds.
Check and/or replace the finisher curl
correction rollers. (Life 250k).
correction rollers. (Life 250k).
AR-FN1/3
“Remove Paper from Tray2” error at
power on.
power on.
T2PF sensor actuator jammed/broken
or missing – replace.
or missing – replace.
AR-FN1
A3 jamming when face down printing.
Incorrect firmware – upgrade to v2.13
or higher.
or higher.
AR-FN1/3
When using staple mode, the capacity
of the off-set tray is reduced.
of the off-set tray is reduced.
Due to the increased thickness of the
stack when stapling, the software
automatically reduces the stack height
depending on the number of sets.
stack when stapling, the software
automatically reduces the stack height
depending on the number of sets.
AR-FN1/3
F1-08
See error code section.
AR-FN2
F1-05, F1-11, F1-14 & F1-15
See error code section.
AR-FN2
BES_S jams.
Check the position of the BES sensor.
If the operator pulls the compiled
bundle before the job is complete, this
will cause a BES jam.
If the operator pulls the compiled
bundle before the job is complete, this
will cause a BES jam.
AR-FN2
Jamming at FJTES.
Incorrect operation of the PRSL
reverse solenoid.
Check for a damaged flapper arm or
the incorrect fitting of the cushion
(adhesive showing).
reverse solenoid.
Check for a damaged flapper arm or
the incorrect fitting of the cushion
(adhesive showing).
AR-FN2
Jamming when printing A3 “Face
Down”.
Down”.
Incorrect firmware – upgrade to v1.03
or higher.
or higher.
AR-FN2
Jamming at entry.
Check and/or replace curl correction
roller. Also check for installed
pressure springs on exit door.
roller. Also check for installed
pressure springs on exit door.
Click on the first or last page to see other AR-405 service manuals if exist.