Read Sharp AR-235 (serv.man9) Service Manual online
AR-235/275 SIMULATION - 4
22
1
Used to check the counter value of each section.
2
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing this
count value with the total counter value.)
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing this
count value with the total counter value.)
3
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
4
Used to check the total trouble (self diag) history.
5
Used to check the ROM version of each unit
(section).
(section).
7
Used to display the key operator code
8
Used to check the number of use of the staple, the
SPF, and scanning.
SPF, and scanning.
9
Used to check the number of use of each paper
feed section. (the number of prints)
feed section. (the number of prints)
10
Used to check the system configulation.
11
FAX related counter display
12
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
19
Used to display the scanner mode counter.
24
1
Used to clear the misfeed counter, the misfeed
history, the trouble counter, and the trouble history.
(The counters are cleared after completion of
maintenance.)
history, the trouble counter, and the trouble history.
(The counters are cleared after completion of
maintenance.)
2
Used to clear the number of use (the number of
prints) of each paper feed section.
prints) of each paper feed section.
3
Used to clear the number data of use of the staple,
the SPF and scanning.
the SPF and scanning.
4
Used to reset the maintenance counter.
5
Used to reset the developer counter. (The
developer counter of the DV unit which is installed
is reset.)
developer counter of the DV unit which is installed
is reset.)
6
Used to reset the copy counter.
7
Used to clear the OPC drum (membrane
decrease) correction counter. (This simulation is
executed when the OPC drum is replaced.
decrease) correction counter. (This simulation is
executed when the OPC drum is replaced.
9
Used to clear the printer print counter. (The
counter is cleared after completion of
maintenance.)
counter is cleared after completion of
maintenance.)
10
FAX related counter clear
15
Used to clear the scanner mode counter.
25
1
Used to check the operation of the main drive
(excluding the scanner section) amd to check the
operation of the toner concentration sensor. (The
toner concentration sensor output can be
monitored.)
(excluding the scanner section) amd to check the
operation of the toner concentration sensor. (The
toner concentration sensor output can be
monitored.)
2
Used to make the initial setting of toner
concentration when replacing developer.
concentration when replacing developer.
26
1
Used to set options. (This simulation is used to
make option setting when an option is installed.)
make option setting when an option is installed.)
2
Used to detect the paper size.
3
Used to set the specifications of the auditor.
Setting must be made depending on the use
condition of the auditor.
Setting must be made depending on the use
condition of the auditor.
5
Used to set the count mode of the total counter
and the maintenance counter.
and the maintenance counter.
6
Used to set the specifications depending on the
destination.
destination.
10
Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL
board is installed.
Scanner. (Setup is allowed only when the PCL
board is installed.
12
Used to input the Software Key for E-MAIL RIC.
Code
Function
Main
Sub
26
14
Used to input the Software Key for the PS
extention kit.
extention kit.
18
Used to set enable/disable of toner save operation.
20
Used to set the job separator paper exit mode.
22
Used to set the specification (language display) for
the destination.
the destination.
30
Used to set the operation mode for CE mark.
35
Used to set the mode of trouble memory.
36
Used to set whether to stop when the maintenance
life is reached.
life is reached.
37
Used to set whether to stop when the developer
life is reached.
life is reached.
38
Used to set whether to stop when the drum life is
reached.
reached.
46
Used to set whether to meet with the output
direction of images regardless of the mode when
installing the finisher.
direction of images regardless of the mode when
installing the finisher.
50
Used to set whether to use the black/white reverse
function.
function.
54
Used to set the PWM duty (brightness) at the
center value of the LCD contrast.
center value of the LCD contrast.
57
Used to set the model code.
60
Used to set enable/disable of the FAX mode key
when FAX is not installed. (When FAX is installed,
the FAX mode is enabled regardless of this setup.)
when FAX is not installed. (When FAX is installed,
the FAX mode is enabled regardless of this setup.)
27
1
Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
(U7-00) detection Yes/No.
5
Used to enter the TAG No. of the copier.
30
1
Used to check the operation of sensors and
detectors in the sections other than the paper feed
section of the copier and the related circuit. (The
operation of sensors and detectors can be
monitored with the LCD.)
detectors in the sections other than the paper feed
section of the copier and the related circuit. (The
operation of sensors and detectors can be
monitored with the LCD.)
2
Used to check the operation of sensors and
detectors in the paper feed section and the related
circuits. (The operations of sensors and detectors
in the paper feed section can be monitored with
the LCD.)
detectors in the paper feed section and the related
circuits. (The operations of sensors and detectors
in the paper feed section can be monitored with
the LCD.)
40
1
Used to check the operation of the manual paper
feed tray paper size detector and the related
circuit. (The operation of the manual paper feed
tray paper size detector can be monitored with the
LCD.)
feed tray paper size detector and the related
circuit. (The operation of the manual paper feed
tray paper size detector can be monitored with the
LCD.)
2
Used to adjust the manual paper feed tray paper
width detector detection level.
width detector detection level.
3
The AD conversion value of manual feed width
detection is displayed.
detection is displayed.
41
1
Used to check the document size detection photo
sensor.
sensor.
2
Used to adjust the detection level of the document
size photo sensor.
size photo sensor.
3
Used to check the light reception level and the
detection level of the original size detection photo
sensor.
detection level of the original size detection photo
sensor.
4
Used to adjust the detection level of OC 20
degrees.
degrees.
43
1
Used to set the fusing temperature in each
operation mode.
operation mode.
10
Used to set the paper feed cycle for postcard.
44
1
Used to make various setups in each mode of
process control.
process control.
34
Used to adjust the transfer current value.
35
Correction temperature setup when correcting the
ambient temperature.
ambient temperature.
40
Used to set the rotating time before toner supply.
Code
Function
Main
Sub
Click on the first or last page to see other AR-235 (serv.man9) service manuals if exist.