Read Sharp AL-1622 (serv.man11) Service Manual online
AL-1611/AL-1622
SIMULATIONS
8 – 4
*
2: Display after clearing each counter 000
(0.75 sec)
3
Blank (0.35 sec)
3
000 (0.75 sec)
3
Blank (1.0 sec)
3
Repetition
7
6
Intermittent aging
After completion of warmup, counting is stopped and the ready lamp is
lighted. When the copy quantity is entered and the start key is pressed, copy-
ing is made to make the set quantity of copies. After 3 sec standby, copying is
made again to make the set quantity of copies. After that this operation is
repeated. The paper size does not matter.
lighted. When the copy quantity is entered and the start key is pressed, copy-
ing is made to make the set quantity of copies. After 3 sec standby, copying is
made again to make the set quantity of copies. After that this operation is
repeated. The paper size does not matter.
1 ~ 99
8
Warmup time display
Execute the simulation input with the copier side cover open, then close the
side cover, and the machine will starts warming up. Warm up time is counted
up every 2nd and it is displayed.
side cover, and the machine will starts warming up. Warm up time is counted
up every 2nd and it is displayed.
1 ~ 99
8
1
Developing bias voltage
output check
output check
Used to out put the developing bias for 30 sec. For the adjustment procedure
of the developing bias, refer to the previous descriptions.
of the developing bias, refer to the previous descriptions.
2
Main charger voltage output
check (Grid bias high mode)
check (Grid bias high mode)
Used to output the main charger grid bias voltage at the high mode for 30 sec.
For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.
For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.
3
Main charger voltage output
check (Grid bias low mode)
check (Grid bias low mode)
Used to output the main charger grid bias voltage at the low mode for 30 sec.
For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.
For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.
6
Transfer charger voltage
check
check
Used to output the transfer charger voltage for 30 sec. For the adjustment pro-
cedure of the transfer charger voltage, refer to the previous descriptions.
cedure of the transfer charger voltage, refer to the previous descriptions.
9
1
Duplex motor forward rota-
tion operation check
tion operation check
<Not Used>
Used to rotate the duplex motor forward for 30 sec.
2
Duplex motor reverse rota-
tion operation check
<Not Used>
tion operation check
<Not Used>
Used to rotate the duplex motor reversely for 30 sec.
4
Duplex motor rotation speed
adjustment
adjustment
<Not Used>
The currently set duplex motor rotation speed set value is displayed. When
the set value is entered and the start key is pressed, the set value is stored.
the set value is entered and the start key is pressed, the set value is stored.
6
1 ~ 13
5
Duplex motor switchback
time adjustment
time adjustment
<Not Used>
The currently set duplex motor switchback time set value is displayed. When
the set value is entered and the start key is pressed, the set value is stored.
50
18 ~ 76
10
Toner motor operation check Used to operate the toner motor for 30 sec.
Note: If this simulation is executed with the toner hopper installed, toner is
automatically supplied to the developer. Be careful of overtoner.
14
Trouble (except for U2)
cancel
cancel
Used to cancel troubles except for U2.
16
U2 trouble cancel
Used to cancel U2 trouble.
20
1
Maintenance counter clear
Used to clear the maintenance counter.
*
2
21
1
Maintenance cycle setting
Used to display the currently set maintenance cycle at the numbers shown at
right. When the set value is entered and the start key is pressed, the set value
is stored.
right. When the set value is entered and the start key is pressed, the set value
is stored.
2
0 ~ 7
Main
code
code
Sub
code
Contents
Details of operation
Initial
value
value
Set range
Key operation
Copy quantity setting: Copy quantity keys
Key operation
Duplex motor rotation speed set value: Copy quantity keys
Key operation
Duplex motor switchback time set value: Copy quantity keys
Key operation/Display
0: 2500 sheets
1: 5000 sheets
2: 25000 sheets (When toner save is ON)
3: 50000 sheets (When toner save is ON)
3: 50000 sheets (When toner save is ON)
4: 150000 sheets
5: FREE (999999 sheets)
6: 10000 sheets
7: 7500 sheets
7: 7500 sheets
Click on the first or last page to see other AL-1622 (serv.man11) service manuals if exist.