Read Sharp UP-3300 (serv.man14) Service Manual online
n
Function
0, 48
Cancels 90° cw rotated character printing
1, 49
Sets 90° cw rotated character printing
[Notes]
No underline is provided for 90° cw (clockwise) rotated characters.
Double-width/double-height setting is reversed.
If “n” is out of the range, this command is ignored.
Double-width/double-height setting is reversed.
If “n” is out of the range, this command is ignored.
[Default]
n = 0
[Reference]
ESC SP: Right margin setting valid
ESC !:
No underline is printed.
Double-width/double-height setting is reversed.
No.
COMMAND
FUNCTION
CODE
28
ESC \ n1n2
Set relative position
<1Bh><5Ch> mn
[Range]
0
à
n1
à
255
0
à
n2
à
255
[Function]
Based on the current position, sets the print starting position through
calculation using the basic calculation pitch.
calculation using the basic calculation pitch.
•
A positive number specifies the print starting position to the right of
the current position; a negative number to the left.
the current position; a negative number to the left.
•
Negative numbers are specified using the supplement of N.
The print starting position is determined through the following calcula-
tion.
tion.
To the right
n1 + n2
×
256 = N
Example
1 dot to the right:
n1=1, n2=0
2 dots to the right:
n1=2, n2=0
3 dots to the right:
n1=3, n2=0
:
576 dots to the right: n1=64, n2=2
:
To the left
n1 + n2
×
256 = 65536 – N
Example
1 dot to the left:
n1=255, n2=255
2 dots to the left:
n1=254, n2=255
3 dots to the left:
n1=253, n2=255
:
360 dots to the left: n1=192, n2=253
:
The distance between the print starting position and the beginning of
the line is as follows.
the line is as follows.
N
×
(basic calculation pitch)
[Notes]
•
•
Any specification that exceeds the end of the line is ignored.
•
This calculation is made based on the basic pitch in the horizontal
direction.
direction.
•
In case of overlapping with the print data expanded currently, over-
printing is performed.
printing is performed.
[Reference]
ESC $: Set absolute position
No.
COMMAND
FUNCTION
CODE
29
ESC a n
Align positions
<1Bh><61h> n
[Range]
0
à
n
à
2
48
à
n
à
50
[Function]
Aligns all the data in one line to the specified position.
The value of “n” specifies the alignment as follows.
n
Position
0, 48
Align left
1, 49
Align center
2, 50
Align right
[Notes]
This command is valid only when set at the beginning of a line. Blank
portions specified by set absolute position/set relative position are
also covered by this command.
portions specified by set absolute position/set relative position are
also covered by this command.
[Default]
n = 0
[Print example]
Align left
Align center
Align right
ABC
ABCD
ABCDE
ABCD
ABCDE
ABC
ABCD
ABCDE
ABCD
ABCDE
ABC
ABCD
ABCDE
ABCD
ABCDE
No.
COMMAND
FUNCTION
CODE
30
ESC c 4 n
Select paper-end
detector to stop
printing
detector to stop
printing
<1Bh><63h><34h> n
[Range]
0
à
n
à
255
[Function]
Selects which paper-end detector causes the printer to stop printing.
When printing is stopped, the line being printed is completed.
Even if printing stop is invalid, the printer stops printing and the print
data is discarded when the paper is out.
data is discarded when the paper is out.
The meaning of each bit of “n” is as follows.
bit
Description
0/1
0
Near-end detector
Invalid/Valid
1
2
3
2
3
Receipt end detector
Invalid/Valid
4
5
6
7
5
6
7
[Notes]
Whether the printer goes OFF-LINE or not depends on the setting of
the dip switch.
the dip switch.
[Default]
n = 0
No.
COMMAND
FUNCTION
CODE
31
ESC c 5 n
Enable/disable
panel switch
panel switch
<1Bh><63h><35h> n
[Range]
0
à
n
à
255
4 – 9
Click on the first or last page to see other UP-3300 (serv.man14) service manuals if exist.